My attempts to configure the Zephyr device tree to run littlefs on an external SD card have repeatedly resulted in what appears to be the creation of a small littlefs instance...
Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
Hello,
I'm trying to make the nrf5340-DK capable of connecting to BLE from multiple devices.
The program is based on: Bluetooth: Bluetooth: Peripheral UART .
I found...
Hi all,
I'm trying to use rtc0 with my custom board build with an nrf9151, but I got a secure fault. I've activated rtc in an overlay file
In my prj.conf
But...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
In order to reduce power consumption , I configured the RX pin of the serial port with an interrupt , and when the device was asleep , it was woken up by an interrupt , and...
Hi all.
What happends on peripheral side when I use long write by sd_ble_gattc_write as devzone.nordicsemi.com/.../ ?
How Can I read it on peripheral ?
Can I use once...
hello there i want to use low power comparator nrf51. now my device work with battery. so i think i require internal reference. now can you tell me how to use internal reference...
Hello, recently I've found an information about bit counter in Radio Module in nRF52 Product Specification. Unfortunatelly I can't find any reference at infocenter how to...
Is MTU of all BLE devices limitted to 23 bytes when using ATT protocol?
I don't know explicitly.
Some say it is possible to use MTU longer than 23 bytes.
Others say...
I am using TAIYO-YUDEN EYSHCN, which is having Nordic-nRF52832 chip on it. As per document from TAIYO-YUDEN, recommended to flash s132-firmware on it. I downloaded s132_nrf52_3...
I have two questions with the remaining unresolved symbols being the most critical. I will decribed the situation I have encountered as a sequrence of chronological steps...
Hello,
I have a need to construct multiple portable devices on a short time frame. We expect that building Arduino-format shields for our peripherals and using nRF52 DK...
I am using PWM on a BLE Nano using Nordic SDK. I was having problems with the PWM and decided I would set the duty cycle to 0 to see if the program was working right:
#include...
I'm trying build a file in Keil, and have received this error below. Please advise on how to fix it! Thanks!:
*** Using Compiler 'V5.06 update 3 (build 300)', folder: ...
Hello,
I'm trying to put a BLENano board to slepp every loop iteration. These are te steps:
setup:
sd_power_mode_set(NRF_POWER_MODE_LOWPWR);
NRF_POWER->TASKS_LOWPWR...
Can someone tell me the best way to build the old bootloader under SDK 12.
Looking in the examples, in SDK12, there is now only the bootloader_secure example
SDK 11...
Hello
I want to know if we can wake up nrf52832 in sleep mode , from a command through an application on a phone via BLE. If its possible can someone please guide me to...
I want to add backtrace functioanlity in nrf52. I am using functions given in below link:
link text
But I am not getting library files for defining functions mentioned...
Hi,
I have programmed a BLE code.
In the code we are continuously connecting and disconnecting BLE connection.
The BLE connection is established for around say 1 sec...
