Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hello. I am using ble_app_uart from sdk14.2. I use pca100401, softdevice s132.
Advertising is generated using timer RTC. Board advertises and stops advertising without errors...
Here is our requirement.
We want to have four transmitters based on nRF2460 and more than 100 receivers. It means there will be four broadcasts.
Each receiver should...
Hi DevZone,
I am working on a project using nRF52840 preview DK and Arduino CAN Bus shield. I modified source code base on some Git Projects. It seems the SPI initialization...
Hi everyone!
I want to implement SPI with "ble_app_beacon" example with the following hw/sw.
DK : nrf52832
SDK : nRF5_SDK_14.2.0_17b948a
IDE : Segger Studio 3.34...
Recently,I use the SDK14 to develop the project,the initial project is in the content "SDK14/examples/peripheral/twi_scanner/pca10056",
Then and the spi example in the content...
I have build the light switch demo, it works properly. But I want to make multiple sensor node that takes data from sensor and send to single relay node. I am little confused...
I just integrated CMock which is part of my unit testing framework and i am trying to test a mocked function however i am running into RAM overflow error. Is there a way to...
May need to post this question to Segger, but I'd figure I'd ask here.
Have a nRF52832 project that compiles, links, and runs fine on the 52832/10040 dev kit board.
...
Hi All,
I am using the nrf52840 to run an application which does not use the BLE.
I need to add firmware update capability to the device so that I can push updated in...
Hi, I am running into a connection problem with connecting to the Secure bootloader example in SDK v13.1, whenever I try to connect I get Gatt 133 error. To my memory, the...
hi,
i doing a project where i have combined light switch server from nrf_mesh sdk 1.0.0 with nrf5 sdk 14.2.0 ble_uart_example to send.
my aim is to send on_off command...
We currently have an application that is running SDK 12.1 on the NRF52832. We have no issues doing a firmware update using the iOS SDK. What we are seeing is a long delay...
Hello, I am running bluetooth example.
I am using the nRF52832 board and SDK 14.0.
I modified the multilink example to make a slight modification and connect it to another...
I have a windows side application and an Android App, both of which are set to capture data from the Thingy Sound Service.
On the windows application, the data after being...
