hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
I'm currently working on an application that collects audio data and sends it to a central device via BLE. Since audio compression has great potential to reduce power...
Hello Sir,
We developed one application in that we use WiFi and interface this to nRf52832 chip using UART. The WiFi Ch_PD(Chip enable Power down = GND for low power consumption...
Hello everyone,
I would like to know how the (G)FSK modulation on nRF52832 is realized. Is my assumption correct, that a Fractional-N PLL in combination with Delta-sigma...
I have the precompiled code running on two seperate nRF52832DK PCA10040 1.2.1 boards. The example appears to do exactly what it said it would do. However I cannot detect any...
I am getting the following errors.
Building ‘1’ from solution ‘1’ in configuration ‘Debug’ Generating linker script ‘1.ld’ Linking 1.elf Output/1 Debug/Obj/ses_nRF_Startup...
Hi,
On STM32 and some other platforms I'm able to get an address that I can write to in order to set the value of a single pin. While (like on nRF) there is one output register...
Hi,
we are looking for a software developer (freelancer) for a Bluetooth LE (BLE) project on a BL652 module. Is there a available developer arround munich / germany.
thanks...
Hello,
Migrating from 1.0.0 to 1.0.1 I've noticed that softdevices in external/softdevice are zipped except SD 132 3.1.0. Does Mesh 1.0.1 break compatibility with SD 132...
Hello,
I do a big scatternet of nRF52840 and i want to deploy code update from a single point. Is there any way to do DFU between 2 nRF52 ? Can a nRF52 propagate it's own...
I am trying the buttonless DFU example from SDK14.2.0. I am not following the testing procedure mentioned at infocentre for SDK14.2.
Followed test procedure:
1. Erase...
I've been using the nrf_twi_mngr_perform() function assuming that my transaction was complete when the function returned. Because of this, I felt safe keeping my descriptors...
Hi Sir/ Miss:
I've a custom peripheral heart rate device.
I use central example "ble_app_hrs_c" to connect it by PCA10040.
After I set up the service (Target_UUID) and...
Dears,
I'd like to add service while connection.
Now I am using UART service and want to add HID service when I put button.
How to add HID service while connection...
I am using Master Control Panel for doing DFU on nRF52832 DK. The nRF52832 is having example dfu code dfu_test_softdevice_w_bootloader_b_s132.hex from sdk11.
nRF51 dongle...
Dear experts,
I'm a new user of NRF52 technology and I use:
Keil µVision v5
NRF52832 (PCA10040)
Keil software pack 8.15 from Nordic Semi
debugger Cyclone...
