When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi,
Is it possible for an 3 party BLE device like an mobile device like an Android/IOS Phones or ESP etc to participate in mesh notwork if so is there any documentation...
I have been unable to perform a DFU over BLE using the bootloader_secure_ble example.
I am using SDK 14.0, nRF52832, S132 with a custom board, along with the nRF51 Development...
Hello,
I want to factory pair nRF52 to nRF52 connections (NUS) with a factory set key but i'am lost.
I digged in NFC pairing but it's too complicated for my understanding...
Hello,
i use IAR EWARM 8.20.2 and SDK 12.3.
I compiled the blank Blinky example from the SKD for the pca10040 without any Errors or Warnings. When i load the .hex to the...
I use IAR EWARM 8.20.2 and the SDK 12.3 because i want to use the S130 for the nRF51.
I installed the provided MDK_8_11_1_IAR and now there are two options for Nordic Semiconductor...
Hi,
Note: i have already posted this topic , but no one helped me , stay hopeless about the solution, so i try again with this new topic.
my problem is :
I tried to...
The comments (and the name of the function) say it returns an address, of an event register. So the return type should be a pointer type? This causes compile errors on stricter...
Hi,
I have two problems with pc-ble-driver, I've tested hrc_v5 example program on my Linux machine, along with connectivity_2.0.1_115k2_with_s132_5.0.hex firmware (using...
We have set the peripheral ADV interval & central SCAN interval as below configs, we found that the connection time is unstable, from 125ms to 980ms, we expect to get a stable...
nRF51822, SD 130 v2.0.1, SDK 11.
Dear community,
I am experiencing an issue with disconnection on iPhone (iOS 11.2.5). After connecting and bonding with device (in iOS...
Hi,
I am using SDK 14.2.0 and SD 132 v 5.
When trying to combine ble_app_beacon with twi_sensor, I get the following error:
..\..\..\main.c(89): error: #253: expected...
I'm developing a project where the device wakes from system_off using a button. I've noticed that it takes about half a second from the time the bootloader starts until the...
I updated the original question
Hi, I am working with two nRF52 SDK13 central and peripheral, with no display, each is connected thought UART to a software interface,...
