This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I recently was trying to test my nrf52 DK. After lot of failed attempts i was able to do DFU update over BLE and also Serial upload .
I am now trying to test the BLE UART...
Hi
According to previous answers ( 1 & 2 ), the limitation on the maximum number of devices that can be added to a whitelist is 8, and is due to softdevice timing limitations...
I have downloaded the nRF51 SDK from here www.nordicsemi.com/.../nRF51822 and I'm trying to run HCI-UART examples as explained here developer.nordicsemi.com/.../a00063.html...
Hello,
I use SDK 13 on nRF52832 with a SD card (nRF port of fatfs lib).
I have a long sleep and i want to minimise current.
With SD card, it's okay i switch off SD...
Originally, this was a complaint about SIGTRAP 0xffffffe while using GDB.
But I've discovered the actual issue is related to a lack of erase/programming of FLASH.
My environment...
I would like to know how long is the minimum pulse width for SENSE to trigger GPIOTE Interrupt from external pins on NRF52832,I have seen
devzone.nordicsemi.com/.../
How...
Hi,
What is the status of a MISO pin of an SPI instance after issuing NRF_GPIO->IN? Does it reflect the real state of the pin? If no, what fast options do I have to read...
hello ,
i have a question, when i download the application.the power dissipation is more than 1mA, and i press the reset key to let the reset pin low level,but it is not...
I have an application that first reads ADC sensor data from a SPI device, then transmits out through BLE. I have a 4ms timer; once it times out
Read sensor data through...
Hello,
I would like to ask your help for examples of nRF52 code, when entering and exiting critical regions (disabling interrupts without switching off a bluetooth connection...
Hey,
just wondering if its possible to lower the pwm driver clock of the nRF52832 to around 500Hz? Im working on a LED dimming application and the LED spots i use have...
Hi,
I got a error fatal awhile after the app switched to low advertising.
Could you please tell me where I can to look into ?
I got the error code 8198 from sd_power_systemoff...
Hi everybody,
Chip: nRF51422
Board: PCA10028
Firmware: S130_nRF51_2.0.1
I found it really difficult to write DMP driver for nRF51.
I've already downloaded motion_driver_6...
