Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I just want to understand concept.
For example, I need transmit battery level, heart rate level and other.. in closed (encrypted characteristic). I use S130 nRF51 SDK9. HRS...
Hello to the Nordic community!
A rather theoretical question: Would it be possible to have a system, comprising of a SoftDevice + Application + Custom Bootloader, where...
Hi there!
I'm looking to layout a chip antenna using the nRF52832 WLCSP chip and am confused about the layout of the antenna matching circuit. The reference design (CIAA...
Hello,
I am using nrf52 with sdk 12.2.0. I am working with example buttonless dfu template aplication by referring to the link infocenter.nordicsemi.com/index.jsp .
I have...
Hello,
I am running a simple application where I would like to listen for BLE packets for 100ms and then transmit a packet. (no soft device) I can successfully capture...
In section 17.1.9 of the nRF51 reference manual it states:
Maximum consecutive transmission time
is defined as the longest time the
RADIO can be active transmitting...
I need to connect VL53Xl to NRF51 DK> I am using latest 12.2 SDK with Keil MDK.I cannot find any I2C(TWI) example. I can find examples for NRF52 based devices. but not for...
I am using a nRF52832 which act as an observer role only and what is observe it send observed data to another device over UART.
When i turn off scanning and just run UART...
Hi,
I generally use " make flash" (armgcc makefile). If there are multiple devices connected I get a pop-up to select a device/emulator to be flashed. This pop-up just defeats...
Hi there,
I'm trying to use nrfutil generate package with an extern key pair generated with openSSL.
I used opneSLL with prime256v1 curve, which correspond to secp256r1...
Hi,
I use nrf51822 with HF XTAL Frequency of 32 MHz
I am migrating from SDK9 S110 to SDK 12.2 S130 and have a problem that the code stop on nrf_delay_us.
#ifndef...
we wrote a small application to jump to a desired address of our application from bootloader , but UART does not seem to work(i cannot see any transmitted values on terminal...
Hi,
I would like to use the ble_app_hrs to send pressure values via the heart_rate_measurement_send function.
Unfortunately, they are too long: around 105000 Pa (equals...
