Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
We am using sdk 12.2.2 and nrf52. We are observing some strange behavior of chip. We have our own customized board.
The issue is mac address shown is different in...
Hi there,
I'm using a PCA10040 board, and the app that I am working on was originally built in SDK 11.0. I'm trying to send a stream of arbitrary bytes over USB using the...
Hello.
I am trying to download a program, but I get this error.
Beacon does not work when downloading in order of Application -> SoftDevice as indicated by the error...
Hello,
In the blinky project, I have added the following peripherals to build up an application
Timer
UART
SAADC
PPI
I have followed the saadc peripheral...
Hi, I want to use the components directory that comes with the SDK as much as possible isntead of the "packs" which comes with keil.
This is what I've selected in a project...
i have two tablets and one peripheral.Now with the code i have i connect to only one device .if i want to connect to same peripheral with another tablet i have to remove the...
Hello:
I have used the nrf52832 .when the radio have get a packet and disable the radio.I find the "NRF_RADIO->CRCSTATUS" register is "1" ,why?how "NRF_RADIO->CRCSTATUS"...
I am developing a BLE remote which will work with Android and iOS(as a remote shutter for camera). I used nRF's HID keyboard example as a base but it does not have volume...
Hello,
we are using the example ble_app_uart_c as basis.
I found out , that it takes about 650ms after Reset / Power up before i can send a string over ble.
The connection...
Hey there, I have a problem when use the command nrfjprog --memrd xxxx.
I was running a simple blinky led example on a nrf52 custom board, then i read some information from...
Hi all,
I am working on a project which receives data from UART (15 bytes at every 40ms interval). I want to store 1 minute of data on the NRF52832 RAM before sending it...
I have peripheral BLE device which can have several centrals in its whitelist. It should be able to connect to central with higher priority first, for example: device have...
Hi
I was using sdk 14.0.0. And I was adopting s332 as a soft device version and I was developing. However, when I go to Nodoric homepage and look for information, there...
I have an application for the nRF52832 which is working fine on SDK 12.3 and I am trying to port it over to SDK 14.2.
After some tweaking I have got the application ported...
I used example ble_hrs_freertos_app of SDK nRF5_SDK_14.1.0_1dda907.
I added one task for LCM (XPT2046) in the example.
i used the function :
When added the display...
