I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello! I am using application that support ANT+ and BLE, so i am using s332 softdevice. now I want to add BLE bootloader feature. (send .bin via BLE). but in SDK v13.0.0-1...
Hello.
Which application can I use to monitor and configure a smart wristband with nRF52832? I would like to check its firmware, update it and see all the info about the...
Hello. I've got issue with TWI and power down mode. I modificated "ble_app_bps" example, prepared own service and characteristic and I added BME280 sensor. And almost everything...
Dear Nordic guy, I'm developing with nrf51822(6.0 stack binary and 5.0 sdk)
I have one question regarding clock.
As I know,automatically,stack go to the sleep mode(HF clock...
Dear Nordic guy, I'm developing with nrf51822(6.0 stack binary and 5.0 sdk)
I have one question regarding clock.
As I know,automatically,stack go to the sleep mode(HF clock...
Hi,
I am trying to alter ANT/BLE relay example to work with multiple ANT+ channels (HRM and BSC), but the program resets after ant_xxx_disp_init() step for the second...
Hello,
I would like to use app timer based on RTC1 in order to wake up the MCU every X sec. The app timer seems to work correctly when the MCU is working. I use the following...
Hi everyone,
We are developing with Nrf52 and it's been a bit of a manual process for us to test our code, we use makefile so we were able to create a clunky system to...
I might need to use SPI and I2C simultaneously in a design, due to the fact that one of the components is only available in an I2C version.
Can the nRF52840 be configured...
Hi
We exposed NFC Type 2 functionality in our nrf52 a while back. Then the NFC SDK got refactored and I had to refactor my code to suite.
Now I am trying to enhance my...
Hi,
We would like to protect our product from people accessing the device via J-Link. We build our application with FreeRTOS. Can we follow this to set it before I start...
Hello,
I want to change data channels after provisioning, I follow devzone.nordicsemi.com/.../ here.
To set,
memset(&new_opt_config, 0, sizeof(new_opt_config));...
Hello Sir,
I am using nRf52832 s132, i want to write program which is automatically ON from sleep mode and after few second it will go system off mode for 1hr.
How i can...
Hi,..My device generated PWM square waves. I can program the frequencies and delays that is desired. but how to modulate current as per our requirement. I need the current...
