Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi,
I can't discover more than 5 characteristics on central with SD130 2.0.0.
I have trided nRF Connect and characteristics were discovered successfuly.
Is there some limit...
Hi,
I have a situation as below.
I have the list of host addresses (public type). Based on the command received, BLE peripheral device should advertise in direct advertising...
Hello there,
We are using nRF52832 custom board. I2C and GPIO are working on it. Then I uploaded BLE program (which is tested on nRF52-DK) but BLE is not showing up at...
Hey Guys,
I noticed when I use nrfutil DFU BLE command on the nRF52 DK the nrfutil program a "connectivity firmware" before the perform the DFU BLE to a Target device....
hai
i have tried to store and update some data in flash using pstorage. on storing data data is stored successfully.
#include "mbed.h"
#include "pstorage.h"
#include...
Hi all ,
hi NORDIC team ,
I'm currently developping a multiprotocol adapter LORA/BLE . I'm using the sd130 .
Semtech's third party says that it's "recommended " to have...
52832，SDK12.0.0
I met such a situation:
In the use of JLink burning program or air upgrade, after the completion of the program card died in initialization low-frequency...
If I am programming a BLE Server device, and I configure a characteristic with BLE_GATTS_VLOC_USER and queue a notification with sd_ble_gatts_hvx(), how soon can I update...
We're developing with SDK 10.0, nrf51, softdevice 8.0.0, s110.
We started with the ble_uart_app and added our own functionality, which includes the timeslot functionality...
the code is
nrfjprog -f nrf52 --snr --memwr 0x10001080 --val 0xabcd0102
I am doing the example infocenter.nordicsemi.com/index.jsp
I am able to get everything up to...
Hi,
I am currently going through the GCC and Eclipse tutorial. Now I struggle to compile the project.
I installed the blinky project (nRF5_SDK_11.0.0_blinky_blank_pca10040...
Hi all,
nRF52840 and S140 support bluetooth 5. Bluetooth 5 expands 8.x adv data length. I test it on the ble_app_att_mtu_throughout example and add more 30 bytes data to...
Hi,
I have a question about choosing "correct" soft device. I need only peripheral connection, but I'm bit in doubt for choosing SD110, because compatible sdk ver 10.0...
what is the function of bsp.h header file. if i use my custom product should i also use this header file?
i am tring to make LED blink with custom port pin. (different pin...
HI, i'm trying to perform the following operations with the Core Bluetooth Framework of iOS:
Connection to peripheral
Services Discovery
Characteristics...
