At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
I have a confusion about mac address of nrf51822, I run example ble_app_uart .
When I use nRF Connect on Android, I can see the mac address of nRF51822 is CB:16:04:4A:10...
Hi,
I use nrf52832QFAA, SDK 11.0.0, Softdevice 132 v2.0.0. I need to add a device_manager_central to my project (in my project it's easier and faster than adding a peer_manager...
Hello,
In the documentation for nrf_serial_write function (SDK 14.0.0) it is written:
timeout_ms Operation timeout, in milliseconds. Pass 0 to operate in non blocking...
Hello friends,
I am trying to flash a nrf51 dk with keil5. When I try to flash it with a multilink universal I get this error:
My settings are the following:
...
Hello everybody !
My code is based on the code of the "ble_app_multilink_central" on which, I added some of the code "ble_app_uart_c" for the initialization and the event...
Hello friends,
I am trying to use the standard uart example of the SDK 11 with the nrf51 dk and trying to update the device's name via UART. I want to save somehow the new...
Greetings,
I can get the ble uart example to work on my PCA10056 using the example hex file, but when compiling the project on the SDK 15.0 S140 it doesn't work. Specifically...
Hi,
I can't found anything in the nrf52840 documentation about the ble antena directionality. I want to use it for indoor location, so i would like to know if it is omnidirectional...
I'm sending int16_t thanks to a custom BLE Service.
I receive well the data on the nRF Connect app (Android), but the data are displayed in hexa, for example for 256 I got...
Hello,
I'm developing an application that will run on a board without externel oscillator for RTC1 and it means no app timers support.
I started from ANCS example and...
Hi, I tested to run BLE Mesh(v1.0.1) light switch example using SEGGER embedded studio(SES) on Windows10 and three nRF52DK(ntf52832) boards .. one client, two servers. It...
Hi,
I encounter the problem when using the mcuboot with zephyr 1.11 is that the system keep rebooting.
mcuboot: https://github.com/runtimeco/mcuboot
mcuboot build...
Reference: bbc micro:bit (microbit) board Eagle schematic files
I heard that bbc's micro:bit board is based on Nordic's nRF51822 & build by Nordic Semiconductors
Since...
Using SDK14.2.
I'm trying to optimize the throughput of my ble_nus-based app (I'm getting about 5k/sec right now). I've read elsewhere on this forum that increasing NRF_SDH_BLE_GAP_EVENT_LENGTH...
Hi.
I am trying to program the ble beacon application example that requires the S132 softdevice. I am following the instructions that request the device be erased first...
