Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
I am trying to start scanning for devices.
I have changed from the example (ble_app_mulitlink_central_s130_pca10028) only
clock source to NRF_CLOCK_LFCLKSRC_SYNTH_250_PPM...
Hi,
I want to know that how if we have Beacon on one side and Development kit on another side so it is possible to communicate them if they are using different services...
I'm using nRF SDK and trying to write firmware to my prototype device. However, nRF SDK doesn't detect my prototype device. I checked the power supply to my prototype device...
Hi,
I am testing example from sdk, 12.2.0, ble_app_uart, nrf52832
And i frequently get a strange behaviour where i don't get a response. And the connection is terminated...
Hello,
I'm trying to set my device on DFU mode by an android mobile application without success.
I'm working with nrf51822, sdk10, softdevice 8.0.
I subcribe to the...
Hi.
I'm using PCA10028, SDK12.2.0, S130 as central.
As I know "sd_ble_gap_tx_power_set" function let me set Advertising Tx power.
How can I set Tx power if i want to...
Hello,
I am going my project with NRG51822 in SDK 11. I build a android app that can connect to my device and access vendor specific service.
My device dedicates one...
Hi, All,
I'm testing multi-connection central function.
And I am struggled in getting relation of address.
AFSK, there are several types of address in BLE.
I found...
Hi.
I'm using nRF51822AC, SDK12.2.0, S130 as central.
After "sd_ble_gap_connect" function, how can I stop this function before connection?
I hope your reply.
Hello,
Is there a way to temporarily disable bonding and just allow any connection? I want to generally use bonding, but there are certain corner cases where I need to...
Hello,
I want to use the FDS libraries in order to store some data into nrf52's flash in my application and I have a bootloader to allow secure dfu by ble.
I manage...
I'm struggling with current consumption. I need my device to completely sleep and leave only the RTC on when the ext power is off (run on battery). After making sure my RTC...
Hy everyone!
I'm trying to write a non-volatile memory position of a device via I2C (twi), the device, a flash memory is the slave.
In my application, I have configure...
Hi I am using the SDK 12 and I am doing some test using the experimiental_app_ble_blinky central and peripheral parts.
I see in this example it use boolean values to indicate...
