NCS 3.0.1 MCUBOOT nRF52840
I am adding MCUBOOT to the coap_client example, which inlcudes snippets in the build configuration (ci, debug, logging, mtd). The snippets are...
I'm trying to implement DFU over USB through Serial Recovery, for a custom board using a nRF52840, following the nRF Connect SDK Intermediate Lesson 9: Exercise 4 – DFU over...
I have been using the nRF54L15- PDK(0.8.1) to test various examples and projects, and everything has been working fine so far. I recently switched to the nRF54L15- DK(0.9...
Hello
I'm currently mounting a LittleFS partition in the internal flash of my Nordic MCU. However, since data is saved regularly to this partition, I’m concerned that the...
Hello
I designed a custom board and now I have to put the code in the nrf52840 module (from raytac). I have been using the nrf52840dk to write my code and now I want to...
I didn ' t use an external 32 . 768 crystal , the internal NRF_SDH_CLOCK_LF_SRC 0 I used。
NRF_SDH_CLOCK_LF_SRC 0
NRF_SDH_CLOCK_LF_RC_CTIV 16
NRF_SDH_CLOCK_LF_RC_TEMP_CTIV...
Hi! I’m currently implementing a hook using mcuboot_status_change() inside MCUboot. I’m following the path defined by CONFIG_MCUBOOT_ACTION_HOOKS , and I’ve confirmed that...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
I copy static void radio_disable(void) and void radio_tx_carrier(uint8_t txpower, uint8_t mode, uint8_t channel) into my project.
I call radio_tx_carrier(RADIO_TXPOWER_TXPOWER_0dBm...
Hi all,
I have a spurious crash in the softdevice I guess.
It occurs sometimes when the master (an HTC-M8 android phone)
rapidly submits characteristic changes
(acknowledgement...
SDK: V6.0
HW: PCA10001
APP: s110/ble_app_hrs
Question:
If use "twi_master_init()" with "twi_hw_master.c", the current consumption is added 1m
A. But if use with "twi_sw_master...
Hi I am completely new to ARM development world. I have been developing for years for PC.
Now I am working on a Project where we have decided to evaluate nRF51822 chip...
I would like to know if it is possible to use the internal RC oscillator without calibrating every 4s with the softdevice disable. I just want to read a sensor every 2s and...
I'm interested in using BT LE to collect data from a number of serial based devices -- a point-to-multipoint configuration. I'm familiar with the UART examples and have seen...
Hi,
i am searching for infos about my concrete BLE-Sig certification situation but i cannot see the forest because of all the trees :o)
i am currently developing a BLE...
Hi,
I know that a lot of question exists on that subject, but I can't manage to have an accurate battery measure on [Nordic Beacon device] (battery CR1632 3V) ( www.nordicsemi...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi,
after reading the nAN-36, I tried to write an application for the nRF51822, with the custom Led Service provided with nAN-36.
I take as a base the Nordic HRM application...
Hello!
I'm using the evaluation kit and i have two questions: firstly, I'm trying to make up a program that allows the communication between two modules, on one side a glucose...
