Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello,
I know that Vdd on nRF24L01 module should be on 3.3V power and probably will be burned if get 5V power.... If in any case that happen at some point of experimentation...
Hello!
The company for which I work is migrating from NRF24 to NRF51.
Our protocol relies on ESB and uses payloads of 32 bytes and payloads in ack (also 32 bytes).
...
Hi,
after receiving button event application crashes. I get NRF_ERROR_NOT_FOUND from app_sched_event_get and device stop responding.
What can be the reason?
Thanks...
Hi,
recently I purchased the nRF51822 Beacon Kit. I downloaded the hw files and unfortunately realized that they are altium designer files.
As I'm using Eagle I would like...
Dear All,
I've recently had a problem with interaction with samsung phones (S3, S4, note 2 on 4.3+) using 51822. The connection interval that I have is around 48ms with...
**nRF8001 + STM32 microprocessor + ble_HID_keyboard_template (from Arduino)**
I am now trying to port the ble_HID_keyboard_template from the Arduino:
After the reset...
Hello support team
Have you tested the nRFgo 1.15 x64?
usually x64 installs in Program Files this installs in Program Files (x86) any reason why?
I had to recover my PCA10001...
is there any complete altium designer file including schematic and pcb file for nrf51822 ?? there is only layout file in the website...... if you have it please email the...
Hi
I just updated our project to files from new SDK release 6.1. The normal application is working properly with the new SDK, but i got in trouble with the bootloader parts...
Hi all
I would like to use the s110 softdevice V7 with the nRF51422 which I know is possible. However, I would like to start the work with an example project, but I can...
I want to make a indoor positioning system using bluetooth 4.0. so for this HOST should recieve the RSSI from the devices it is connected to(from RSSI to distance conversion...
Hello,
I am working with the nRF8001 device:
When I try to configure the device as a service data broadcaster and go to the nRF8001 Setup -> Generate Source Files (in...
For improving my data trouchput (both directions, using »Write without response« and »Notification« like e.g. nRF Uart Example do9, I'd performed some tests regarding the...
