Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
I built a device using the nRF52832 SOC, have programmed it with the Version 16 SDK>ble_app_uart_pca10040_132 using Segger Embedded Studio. I am able to connect to the nRF52...
Hi,
We are developing a product using NRF52832 chipset with a small 128*160 LCD (based on st7735s controller using 8 bit parallel interface).
I noticed that there is st7735s...
Are there any limitations that will not allow me to make the ble_app_hids_keyboard example with FreeRTOS?
If no, is there any examples that will help me easier to migrate...
Hi,
I see that Eddystone packets has service data limited to 20 bytes frame data. But unfortunately I have to encode more than 20 bytes.
So can I use advertise mode as...
Hello everyone.
I have made the next solution for merging softdevice into debug fw.
i 've added the next lines in ld script
MEMORY { SD_FLASH (rx) : ORIGIN = 0x00000000...
Hi,
I want to output a high & low voltage with an array, the array contains a sequence number, looks like: {0, 1, 0, 0, 0, 1, 1, 1, 1, 0, ...} , and the length of the...
I'm wanting to create and Android application that can communicate with a nrf24l01 module. Is there an android library available that will permit this? Thanks in advance!
Hello Everyone,
Consider i have 2 MCU's on board connected via UART interface, one is any ( Target ) MCU (MSP32, STM32, etc) and the other is Nordic's nRF52832 ( Host )...
Hi,
We have two nRF9160DK and both have the SIM card issue as below, and our development was blocked by this issue, so please help check it, thanks!
original case
Hi!
I am trying to figure out the app_timer_library but am running into some (to me) strange behaviour. For the first seconds it appears as if the LFCLK is running much...
Hi,
I've built a application based off of the ble_app_hrs_rscs_relay_pca10040_s132 example in SES using a Laird BL652 module (nRF52832 underlying device). Presently the...
Hello
I successfully build asset tracking example , for nrf9160_pca10090ns
when I try to run using segger, I get the following:
SPM: NS image at 0xc000
SPM:...
Hi,
I am trying to use the Android-BLE-Library with my nRF52832 device (I do have another test Android app which can work w/o using the library).
I followed the Github...
I am porting RF evaluation code to the nRF53 NCS/zephyr/Segger Embedded Studio toolchain, using only the network core to start.
How do you recommend configuring the network...
