We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hi,
I tried out the light switch example on a nRF52833 and it seems not to be reliable at all. So i connected the debugger and saw, that in access.c,
in packet_alloc_and_tx...
Hi all,
I am trying to use nrf52840 dongle as hci_usb with the very simple task: scan
Host is Raspberry Pi with BlueZ
Controller is nrf52840 dongle with firmware hci_usb...
Hi
I want to move DFU at the application level. Is this possible? I want to move DFU at the application level because of my project requirement.
1. In my project, I have...
Hi, I am trying to get the BLE values on Thingy91 (PCA20035) . And I have followed the
devzone.nordicsemi.com/.../217018 I have ported the diff (nrf and zephyr diffs from...
I am using built-in DTLS for encrypting my UDP traffic. In order to save expensive data quota and reduce battery drain, I have to make use of session resumption, so that I...
Hi. I have a question about Bluetooth 5.1. I just want to know what the main difference is between a Bluetooth 5.0 and Bluetooth 5.1 chip.
Is it the hardware or software...
I am developing a firmware on a nrf52840 board with FreeRTOS. Unfortunately, due to a mistake during the development process, the board misses the XTAL 32,768 Hz.
Is there...
Hi Nordic:
I want to build a raspberry connected to a 52832 board via uart,
this raspberry pi with 52832 board need doing secure DFU to remote BLE device, the raspberryPI...
Using the nRF9160 on the Verizon network we are having some issues with eDRX. Specifically sending data to the device from our MQTT server.
We have configured a eDRX interval...
Hi,
I am working on nrf52 msc example. I am required to use internal flash for msc. In example there is support for ram, sd card and spi flash. I am required to use internal...
Hello,
I'm currently trying to sniff the DH Key Exchange as specified in Spec 5.1 p.2446. I'm using the nRF51 Dongle as sniffer, the nRF52 DK as slave and the nRF52840...
Hi,
I am using two nRF52840 DK in which one of the board is flashed with light switch client and other one is flashed with light server and a nRF mesh app is used for provisioning...
Hi,
I see Nordic has recently released an updated software to do direct test mode (without the use of python or the old nRFGo studio). I am able to run the test code on...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image.
1) While upgrading over serial interface using DFU, whether UART needs...
Hi,
If you are interested I would to contribute to https://github.com/NordicSemiconductor/nRF-Sniffer-for-802.15.4 repository. On the python driver part. You could allow...
