Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hi ,
I am working on NRF DFU firmware update. for that i am using secure bootloader code .
I tried with the of way of flasing bootloader code on my custom board and sent...
Hello Nordic community,
I updated latest modem firmware v1.1.0 in nRF9160 custom board. After flashing application code into custom hardware I power off and power on board...
Hello,
I have a question about hardware for Bluetooth LE Audio.
I see Nordic is working on a dev kit:
https://blog.nordicsemi.com/getconnected/le-audio-unveiled-as-the...
HI
I am programming NRF52840 dongle using nrf52840 dk
i have flashed blinky code to my nrf52840 dongle it programmed sucessfully after that i have erased the dongle by...
Hi there,
I'm trying to use the aws_fota example with nrf9160 and AWS and it works fine. The problem is that in my country we don't have LTE-M, so we decided to use a...
Hi,
My application returns ERROR 8 [NRF_ERROR_INVALID_STATE] after I click disconnect in the app "nRF connect for mobile" .This error is returned by "ble_advertising_start...
I try to run samples/bluetooth/scan_adv on nRF52840/nRF5340 using nRF BLE Controller..
Result is nRF52840/active scan: 498 packet/s nRF52840/passive scan: 507 packet/s ...
i have done read and write operations on fds with dummy buffer. now when im writing new data into fds it is showing the previous data .can anyone give the function to erase...
I am trying to build a solution based on the nrf_ble_uart_c example. Building has been working fine until I added pin configuration statements.
I've tried relocating the...
I am incorporating the "pin_change_int" code to generate GPIOTE interrupts from an external device. I made a couple changes including renaming the function from gpio_init...
Hello,
I've been playing around with with the nRFsniffer for a couple weeks now. Adafruit was out of stock of the BlueFruit LE Sniffer so I ordered a BLE400 and a few Core51822...
I would like to program the NRF52810 with the SoftDevice 132 and my bluetooth program. Is there any way to reprogram the NRF52810 over bluetooth rather than using a wired...
Hi,
I'm wonder is the speed of i2c on nrf52832 can be faster then 400kbps? even use EasyDMA, the speed still can't faster then 400kbps? I also look into the max speed of...
Hello All,
I am a bit confused with the maximum speed that is achievable with the USBD CDC ACM driver.
In Previous threads like this:
https://devzone.nordicsemi.com...
I developed a functioning application that advertises with Nordic UART Service, connects to a smartphone application, then reads various sensor data using the SAADC and transmits...
