HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
i changed the code to send environment data over ble_nus service and it was worked
so i tried to send motion sensor data over ble_nus service and i changed code but no data...
Im developing a mesh network based on a custom board using the nRF52832.
I fine with sending some bytes over mesh . But now i want so send more bytes over mesh using Instaburst...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
I have few queries on setting Tx power...
Today ,I look up the SDK revisions，found that SoftDevice S130 V2.0.0 support NRF51822 V3.Now my production use S130 V1.0.0,but Chip revision unknow(N51822 QFACA2 1921DC).Is...
I have an application based on ble_app_hrs_freertos from SDK14.
Sometimes the application will not start advertising. When this happens, it does not help to power-cycle device...
Hello, I start in programming on nrf9160 DK. I followed the tutorial "getting started part 2" (https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started...
Hello,
Good Day!!
My question regarding the reset functionality of the device.
Reset the device on the short press of the reset button and on Long press (for example...
Requirements:
Transmit an advertising packet that can be received by a native IOS App & a native Android App.
Using an nRF52810, I need to set it to Advertising (non-con...
hi,
The data is sent to the app by sd_ble_gatts_hvx(), but the data obtained by this app is wrong.
When salve sends a byte, the data obtained by the app is always 0,but...
When I download \nRFready Smart Remote 3 nRF52 v1.2.1alpha\nRF5x SDK-SR3\examples\ble_peripheral\smart_remote_3_nrf52\Projects\Firmware_nRF52832 to my 52832 device, I can...
Hello everyone,
I am modifying the ble_central_uart example to connect directly with a device using its MAC address. For some reason I don't understand, it doesn't find...
I am getting an NRF_ERROR_INVALID_ADDR when using the SDKv15.2.0 call nrf_sdh_ble_enable() with softdevice s332v6.1.1
The ram start address provided to the function is...
Hello,
I am creating a wearable PCB with the Raytac MDBT4Q-P BLE module, which uses the nRF52832. I need this device to have OTA firmware capability, but I'm finding it...
