Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
In Beacon Why UUID is required ? Where exactly it will be useful ? I understand Major value Minor values , company identifiers values . it will difference the beacon location...
Hi guys,
i'm trying to deploy a BLE iBeacon on an Holyiot-17120 board. My code runs fine on the nRF52840 USB Dongle DK, but on this board works only when I've debugger...
Hi All,
I want to configure 64 MHz internal oscillator (HFINT) on my nRF9160 DK to reduce the wakeup time of nRF9160 chip from system-off mode. Is there any example available...
Hello,
I'm looking to be able to adjust PWM output frequency around 100KHz in 100Hz (or close to it) steps. I understand that no matter which method you use the implement...
Dear all,
I'd like to customize bootloader, I need more space so i modified flash address from example: FLASH ADDR (0x78000), SIZE (0x6000) to FLASH ADDR (0x69000), SIZE...
I am using the code above and already try it in the compiler . It should work but when I try to display in termite it only display .000 for microseconds.
Example
1987...
I used thingy s132 pca20020 sdk and i changed the code.
send data.accel.x, data.accel.y, data.accel.z data when data over the limit in swith case DRV_MOTION_EVT_RAW in drv_motion_evt_handler...
Hello all!
I've been researching DFU over BLE, between a central and a peripheral.
The peripheral is possible to upgrade over the DFU Bootloader. I've tried upgrading...
Hi,
I try to use cmake in Linux to get the hex file fo bootloader. The Platform is nrf52832_xxAA, the toolchain is gccarmemb. I read the given cmakelists but many variables...
Hello!
I am in the final phase of development and currently focused on reducing power consumption of my device.
To improve power consumption I'd disable UART if not...
Hi,
I am using nrf52 DK board.
After uploading my bootloader and application on a device that is connected through bluetooth with my board, i want to know the application...
Hi,
i'm facing a problem with a connection.what i understand from ble there are 2 mode in ble such as advertising mode and connection mode. i'm working on a project, which...
I have designed a custom board using NRF9160, but it has some trouble such as can't connect to LTE/NB-Iot, detect GPS signal,... So I want to use development kit to set up...
Hello,
SDK: 15.3.0
nRF52840-DK
IDE: SES
Example: flash_fds_s140_pca10056
Example Location: nRF-SDK\examples\peripheral\flash_fds\pca10056\s140\ses
Example Documentation...
It builds OK and I can flash the hex file using nRF connect Programmer. But I need to debug the code but I have not found a way to upload the code and break at main() entry...
