I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Hi,
I have couple of nRF52832 boards, nRF5-SDK-for-Mesh (v. 0.9.2) and good will to demonstrate some simple multihop mesh.
I already tested the light control example...
Hello,
There is gonna be a tech tour in my country(Israel) soon and I am planning to purchase 2 nrf52832 Development kits does anybody know if it will be available there...
Hi! I want to use the "cube" animation from android thingy app, with my custom board.
When I scaned in first place I couldn't see my board. It was solved adding the ble_tcs...
Hi,
Is it safe to backfeed some current into the PPK.
I use the PPK to measure the power consumption of a battery powered IoT device. I disconnect the battery and use the...
It looks like the "NRF52-DK" development kit I can find comes with an nRF52832 chip, but I'm looking to get a dev kit to develop for the nRF52810. I did also find a "NRF52840...
Hi: it's me again, sorry to bother everyone once more.
This time I can finish provisioning... almost. You see, at the end of the whole provision process, a function must...
Hello,
A stupid newbie question: APP_UART_FIFO_INIT seems to get stuck while trying to run
example code.
Only modification I have made is the usage of SEGGER_RTT for...
Hello,
I was having some trouble communicating with another slave device thru TWI, I was not receiving his ACKs.
So I decided to try to turn off internal pull ups following...
I'm using S132 (SDK 12.3) and I'm trying to perform DFU over the air. The procedure I am using with this device (and failing) is being used on other devices an succeeding...
Hi everyone,
I'm trying to compile my own bootloader. I had this error when trying to flash it into my module:
Here is my linker script for the bootloader:
SEARCH_DIR...
I want to write data longer than 20 bytes on Android MCP.
But if I use "write command", only 20 bytes data can by successfully written. The rest data is lost.
If I use ...
The last time, i could wireless communication by pressing a botton.
The next time, i wanna send the data to phone if the communication is established.
i modified the source...
There are already a few threads about this problem but none of them helped.
I want to use GPIO9 + 10 as .. well .. GPIO.
Here's what I did:
added CFLAGS += -DCONFIG_NFCT_PINS_AS_GPIOS...
hi,everyone,i use the nrf52832,sdk11.Every now and then my hardware has reset,and l use the "NRF_POWER->RESETREAS" to read the reset cause, and the NRF_POWER->RESETREAS value...
I have gone through the SDK and from what i basically understand is that gazell and BLE Multilink look very similar from the application point of view(1 Host connecting to...
