Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi there,
I want to use a LiFePO4 Cell to supply the nRF9160:
Is the MAX17224 suitable to power the nRF9160?
Is this Power "Sequence" OK? Productspecification nRF9160...
currently we are facing an issue with our testing that, our product battery is getting drained to 0 volts. we understand that we need to put a cutoff voltage from the firmware...
Hey folks,
I'm developing a long-range application with nRF52840 DK that (optionally) uses NUS (Nordic UART Service) to send data to Samsung S10+; there is no problem establishing...
Hello,
SDK 15.3.0
nRF52840-DK
s140
IDE:SES
I am running into an issue using the app timer and LPComp together. The error is NRF_FAULT_ID_SDK_ERROR, With RTT output...
Let say during the normal program flow I want to change often the edge direction which will trigger the event: rising edge, none, falling edge, none … Can I work direct with...
hi:
i want to know CKCON config is CKCON =0x01 or CKCON =0x02? because datasheet is CKCON =0x01
External data memory stretch control. 001: One stretch cycle (default)...
Hi All,
I'm working with Nordic BLE Mesh and trying DFU (OTA) provided in sdk for Mesh.
I used \doc\getting_started\dfu_quick_start.md as the guide to setup and test...
Hello,
I am using nRF52840. I am trying to get hands on DFU. Without any modifications, I am using examples as is.
1) I followed below steps to do DFU hrs_application_s140...
I am looking for some 'getting started' information on configuring the nrf52833 DK for direction finding.
I have read the thread: https://devzone.nordicsemi.com/f/nordic...
Hello,
I have made a custom board based on NRF52840 IC.
The board is using GPIOTE, SPI2 and TWI1, and when put to sleep, consume 665µA. When just initializing the SPI...
Hi,
I would like to read accelerometer value from orientation_detector_calibrate() (in asset_tracker/src/orientation_detector/orientation_detector. c).
But from main.c...
Hi,
I am learning nRF development with 52DK device and SDK v16.0. I noticed that by default the 52DK planned P0.5~8 for UART purpose.
I am wondering if I can disable UART...
Hello ,
I am trying to send 1,000 of MPU-9250 data from NRF5832 peripheral(ble_nus_uart) to NRF52832 central(ble_app_uart_c).
And i have been searched this site and set...
I would like to move existing nRF9160 solution created according to nrfConnect Getting Started Guide to another directory under Windows.
Simply moving the folder doesn't...
