Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
I'm writting firmware for a Peripheral Server and wish to display the smart device friendly name that will connect to my nRF52832. Is it possible without addind service/characteristic...
I am Planning to Implement Card sniffing with NFC Front Chip !
Can I Utilize Comparator for card presence detection system senses the card by measuring the decay time of...
Hi
The slave select (ss) pin during the spi communication is always low even when i make it high to release the spi bus. It looks to me that I'm not actually controlling...
Hi All,
I got 66uA current consumption in sleep mode and trying to reduce it further to few uA. I have disabled the serial interface and still wondering if there is anyother...
Hello All,
I am working on the nrf52810 module.
I am using sdk 15.3 with softdevice 6.1.1. (IDE segger)
Issue-
1. I am giving the Advertising name as " TEST_01 ...
Hi everyone,
this is my first question in this blog.
I am trying to use the library pc-ble-driver-py in order to interact with a DevKit (in which an example code is implemented...
Hello!
I want to use a long range and buttonless bootloader in nrf52811. S140 cannot be used for this task, because S140 use more then 150KB of flash.
Is it planned to...
I need to download nRF Sniffer v2.x, but the link is not valid, please send me a valid link
Old unavailable address: https://www.nordicsemi.com/Software-and-Tools/Development...
Hello,
I have to send hardcoded AT commands on button press on nRF9160dk. So for that, first I did program for button press. It is working fine. Then I did simple_at program...
Hi,
SDK: nRF5_SDK_00.11.00 ; S132 SoftDevice v2.0.0
I am working now to migrate my application from DM to PM (in order to better handle pairing&bonding).
Sometimes the...
Hi team, there is nRF52840 connected to STM32 via UART, the goal is to receive STM32 firmware over BLE (using nRF52840) and send the firmware to STM32 via UART.
My goal...
Hi!
I am realizing a comunication between a serial device and the nRF52832 through UART; i set PIN 5 for TX and PIN 10 for RX (after set PIN 10 for GPIO use) and i don...
