Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I have a need for an interrupt to go off at a 4khz rate. For this, I am using a repeated App Timer (running off the 32k crystal).
Prior to adding this extra timer, we used...
I'd like to run the DK in at the lowest power in SYSTEM_ON mode.
It's my understanding that the ble_app_gzll example places the system in the "low power" SYSTEM_ON mode...
Hello Folks
I would highly apprciate if anyone can point me in the right direction here
After lot of consultation we imported a smal size shipment (of about 1000 nRF51822...
Connection_mode_with_1sec_Notification.jpg
In my BLE project I am using connected mode, and I found that the current consumption is very high ~190uA during idle mode. I...
I'm currently working with an own hardware with a nRF52840. We had some time to get the radio working, because we copied the schematic of the PDK. In the reference design...
Hello I am using sdk version 14.0 and softdevice S332. I am looking at the ANT + bsc code. I have two questions when looking at this code.
bsc_tx could not see an event...
Hello guys,
Please help me on this.
I want to erase BMD 350 chip using BMD 300 erase and recovery software tool. But I can not do it.Error comes as per the attachment...
Dear all,
I want to create a star network, composed by one gateway and a limited number of nodes. The nodes periodically send information to the gateway. I am using the...
I'm running the HID Keyboard example from SDK 12.2.0 on nRF51-DK with SD 130.
When I long push Button1, it disconnects for a moment and connects again immediately.
Events...
I am trying to make a custom application in which I need to connect to a device and read/write its characteristics' value.
But my target device has had 4 primary services...
Hi Nordic Engineers!
we bought 110 nRF52840 IC's for Field tests.
10 of them marked Q1AAAA / 1716AK
another 100 marked Q1AABB / 1745AC
What is difference between series...
Dear Nordic Team,
Thanks for supporting.
Now i am work with secure dfu using SDK12.3.0.
My Hardware :PCA10028
nrfutil version 3.1.0
Create Zip file like : nrfutil...
Hello.
I want to design a product. It will have these features;
It has 4 buttons on it.
Obviously it is battery powered device.
I want to see some information...
Hi
I have made ble scanner using nrf52 and I have set uart baud rate 921600 and sending scanned beacon to other micro-controller for processing but It does not scanning...
Hi
I'm looking for an example on how to write a hex-file to SoC using nrfjprog.dll.
The P/Invokes are all set and working fine.
I'm absolutely not familiar with python...
