Hi,
I'm using the nRF52840 with the SoftDevice for BLE. In my system, it's primarily a BLE transceiver controlled via SPI by an external TI MSP430. We're considering implementing...
Hello,
I'm looking for guidance and understanding of how to properly use the KMU and ITS for secure key storage of a key generated on device.
I see that typical ITS use...
Hello,
I'm currently using Visual Studio Code with the newest SDK, Toolchain and Plugin on MacOS and most of my applications are freestanding applications.
Now I want...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Hey everyone,
I'm new to the Nordic/Thingy/Embedded world and was hoping I could get some hand holding to achieve a simple change.
I would like to change the Thingy...
Hi All,
I am working printer project where i will be using two boards , one is nrf51 dongle which acts as client(sends/advertise the data) and another is nrf51422 soc on...
Hello community,
I did a central device which is connecting with 8 slaves and this slaves are sending every time 8 bytes when they are connected. My set up is the following...
I'm trying to create a program that takes a stream of UART data at 115k baud streaming in and sends it over BLE as fast as possible. So far, I've
(1)Verified/ made some...
Dear Nordics,
If I add ble_nus service to buttonless_dfu example , it will reset after ble_dfu_init(). If I set
*p_ble_enable_params->common_enable_params.vs_uuid_count...
I am working on S140 on nRF25840. I am using the ble_app_beacon sample.
I want to set the advertising interval smaller than 100ms while using non-connectable mode. But the...
I am developing a product where I need to read a signal from an SPI ADC and send remotely to a receiver. This will be powered of a coin cell.
I see that the NRF51422 is low...
Hi,
I am trying to program nrf52 (on board ), but I keep getting these error:
$ nrfjprog -f nrf52 --program nrf52832_xxaa.hex --eraseall
ERROR: JLinkARM DLL reported an...
Hi,
I'm trying to connect and discover services of a BLE device equipped with a nrf52832. The device advertises correctly and i can see it on the nrf Connect app on both...
Hi All,
i would like to know how gpio relate to gpiote,i go through some code and find
out , that gpiote handles in,out,config registers that is handle by gpio also ...
Hi nordic guys,
I have built a project based on ble_app_hids_keyboard demo in SDK12.3.0.This is a new hid deive which is microsoft defined in win10.The sample report is...
I have few questions on BLE in rigado based on my requirement needs,
I need Dynamic data transfer in beacon mode, is it possible in Beacon mode without Rigado BLE stack...
Hello,
I get two errors when compiling examples\ble_peripheral\ble_app_uart with IAR 8.11. I have ble_app_uart_pca10040_s132 - nrf52832_xxaa as the active project.
I...
registered_handler_get() in ble_db_discovery.c searches a table for the appropriate handler to call for a given UUID.
However, ble_db_discovery_evt_register() assigns the...