I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
According to the description of S132_SDS_v5.0 on page 82, when the establishment of connection, in accordance with the BLE protocol, softdevice will be interrupted frequent...
I am using nRF52840 and the power profiler. I am trying to measure the current to evaluate the scheduling of BLE. Now I am using the ble_uart_c example and I changed the scan_interval...
I'm trying to set up SPI example from SDK12.3, but I get error at line 53 of main.c
static const nrf_drv_spi_t spi = NRF_DRV_SPI_INSTANCE(SPI_INSTANCE);
It's saying...
Dear friends,
i am using Power Profiler Kit with a nRF52832 DK(PCA10036). However, i just find three versions of SDK on www.nordicsemi.com/.../nRF52-DK . My problem is that...
Hi nordic,
nRF5_SDK_14.0.0_3bcc1f7\Raga\examples\ble_peripheral\ble_app_ancs_c FDS\pca10040\s132\arm5_no_packs
I had a problem when I was using FDS，When I use the GC...
Dear friends,
I want to use Power Profiler Kit to monitor the current waves of nRF5x DK, and i followed the following configurations:
The PPK board (PCA63511) is connected...
How do you do
Now use E: \ Nordic \ nRF5_SDK_12 2.0 \ examples \ peripheral \ pwm_driver \ pca10040 demo5 pwm_driver routine
There are two problems:
How to change...
I run into this topic during seeking an answer to my problem and for me, as well as for the author of that question the answer doesn't work properly. But wouldn't it be easier...
I was able to create a Distribution package with the command as shown in the following photo.
I have taken the zip file from email app in my iPhone and have opened in...
Programming the bootloader
How the MBR knows the start address of the bootloader?
pape says : This start address is defined in UICR.BOOTLOADERADDR, which is located at...
How do you do
1.Now want to set the PWM output frequency is 60 hz, but with an oscilloscope test is 60.24 hz, here more than 0.24 hz.How can I do the precision of the precision...
Hello,
I'm trying to connect my Linux computer to the nrF52 DK card using BLE.
I'm connecting my Bluetooth chip to nrF52 and I want to display "hello" on the serial interface...
