I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi, I want to use the components directory that comes with the SDK as much as possible isntead of the "packs" which comes with keil.
This is what I've selected in a project...
i have two tablets and one peripheral.Now with the code i have i connect to only one device .if i want to connect to same peripheral with another tablet i have to remove the...
Hello:
I have used the nrf52832 .when the radio have get a packet and disable the radio.I find the "NRF_RADIO->CRCSTATUS" register is "1" ,why?how "NRF_RADIO->CRCSTATUS"...
I am developing a BLE remote which will work with Android and iOS(as a remote shutter for camera). I used nRF's HID keyboard example as a base but it does not have volume...
Hello,
we are using the example ble_app_uart_c as basis.
I found out , that it takes about 650ms after Reset / Power up before i can send a string over ble.
The connection...
Hey there, I have a problem when use the command nrfjprog --memrd xxxx.
I was running a simple blinky led example on a nrf52 custom board, then i read some information from...
Hi all,
I am working on a project which receives data from UART (15 bytes at every 40ms interval). I want to store 1 minute of data on the NRF52832 RAM before sending it...
I have peripheral BLE device which can have several centrals in its whitelist. It should be able to connect to central with higher priority first, for example: device have...
Hi
I was using sdk 14.0.0. And I was adopting s332 as a soft device version and I was developing. However, when I go to Nodoric homepage and look for information, there...
I have an application for the nRF52832 which is working fine on SDK 12.3 and I am trying to port it over to SDK 14.2.
After some tweaking I have got the application ported...
I used example ble_hrs_freertos_app of SDK nRF5_SDK_14.1.0_1dda907.
I added one task for LCM (XPT2046) in the example.
i used the function :
When added the display...
Hi,
IC : nrf52832
SDK : Mesh_v1.0.0
I am testing the light_switch demo of the Mesh_v1.0.0.
I don't have 32kHz osc on my server board, so I have to change the clk...
Connect USB to PC, no "JLINK" device. But connect USB to PC and press reset button at same. I can see "BOOTLOADER" device.
How can I get my board to normal?
I am trying to create a network mesh using the multiperipheral example.
In the original version the communication is possible only:
central >> peripherals
peripferals...
