app : nrf tools on git hub
s130: sdk v11
s110: sdk v8.1.0
example : nrf_ble_uart.
after modify, it happen, is there some definition shoud modify in app?
by the war,the...
Hi......
the board advertising correct,and it work normal (connect,send and receive data),bug it's name can not display in app scan menu. the definition is "liu",but displaying...
HI,
with the new version of the bluetooth website, i can not find the link to overview the profile,service,characteristic and something else related to it.
thank you.
I've developed my BLE application that is based on nRF518822 and softdevice S110 v.8.0.0.
I've defined 6 services (4 with 2 characteritics each and 2 with 1 characteristic...
I can get right value when I chose QDEC_SAMPLEPER_SAMPLEPER_512us in slow application ,but in my application my max data rate is more than 2k, so the QDEC value is less than...
nrf51822 SDK 9.0
iphone 6plus System version IOS9.2
When the phone receives the QQ message "static void notif_print(ble_ancs_c_evt_notif_t * p_notif);" can execute.
but...
Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Hello,
I am currently evaluating options for integrating Bluetooth Low Energy (BLE) functionality into a medical-grade device that requires time-sensitive communication...
Hi,
I recently checked support of MCUBoot validation and from NSIB for nrf54l15. (sdk 3.0.0 and above)
During this, I enabled Signature algo as ecdsa-p256.
And...
There are two USB ports. IMCU and nrf5340. I had a lot of trouble with bad cables but i found one that works and I find that I have a jlink drive that pops up so I know there...
Hi Sir
The npm1300 allows setting the default voltage using resistor values as shown in the table below. However, if I want to set the voltage to 1.05 V using resistors...
I am working on synchronizing RTC timers on several nrf52832s and i would like to have a single clock clocking all the RTCs on all the boards. I understand that the LFCLK...
I thought I had been extremely careful to _not_ brick the device, but apparently I did.
I created a firmware-dfu.zip file, even with appropriate keys, etc. as below.
...
We're developing a low-power application on the nRF9160 where we need the device to stay connected to the server over LTE, so we cannot enter System OFF mode. Instead, we...
Hello,
I am developing a product using the nRF54L15 and have noticed a discrepancy in the documentation regarding clock pins. My intention is to use pins 1.02 (SDA) & 1...
Describe Need to repeat disconnect/connect cycle after BT timeout. Problem is when using UART over BT with Nus Shell when connection is terminated by timeout (for example...
How to prevent storage partition from erase durning MCUBOOT firmware update?
I use Settings with NVS to store data
CONFIG_FLASH_MAP=y
CONFIG_FLASH=y
CONFIG_SETTINGS...
Hi, It's looks like I bricked my Thingy:91x . It was working fine when I program it with the target " thingy91x/nrf9151/ns " then later while learning I try program the in...
Hello,
I've got some questions regarding the use of DFU target library. I get my update data from the UART and like to use a setup with two partitions on my device. Is this...
Hello, I am new to android development. I am building an Ble App for some of my work in which I want to include Direct Firmware Upgrade(DFU) over-the-air.
I have building...
Previously, I designed a PCB for the nRF52832 chip using the RFANT3216120A5T antenna ( link ). However, I was only able to achieve a very limited Bluetooth range of around...