Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I have two devices, one is a beacon (DEVICE #1) and the other (DEVICE #2) collects information from the beacon. I'm advertising with a transmit power of 4dBm. I want to reduce...
I have previously had success with programming the nRF51 Series using the nRF51 DK and want to use the nRF52840 DK to program a nRF52840 that will be run in High Voltage Mode...
From the cmakelists of bootloader in Meshv320src, I found the code "create_hex" but this code cannot found in CMake's document. How can it work to generate the hex file?
I am using SDK 15.3 and wanted to ask that if there is a while loop where I can check flags and increment tickers. The program at the moment gets stuck inside
Suggestions...
hello, I have two questions for SAADC of nrf52832 when we use nrf52832 SAADC for voltage measurement.
The AIN0 is connected to the pin to be measured(the voltage is about...
Hello, I encountered the following error when compiling the SDK16.0.0 with keil5.26, how to solve it?
compiling system_nrf52840.c... RTE\Device\nRF52840_xxAA\system_nrf52840...
Hi,
I am using nrf52832 with softdevice s132. The peripheral device is nrf52832 and central device is a mobile app. I want to disable BLE in nrf52832 and I am using this...
Hello,
I have tested the example code of the nRF-IEEE-802.15.4-radio-driver and now I'd like to modify it.
How I can disable the ack? (I tryed this function: nrf_802154_auto_ack_set...
Hello
SDK 15.3.0
4 year old post describing flash storage libraries:
https://devzone.nordicsemi.com/f/nordic-q-a/13821/difference-between-persistent-storage-libraries...
Hello
I try to use this bootloader https://github.com/williamhuang03/STM32F4-Custom-Bootloader on STM32F4 which works well through cable but as suddenly I use Nfr51 as transmitter...
Hello All,
I want to perform an Rx blocking test for my nRF52840 BLE chip which is installed on my custom board. I wan to transfer the packets from device to other, and...
I take the external PWM signal, I directly used the method of controlling the GPIOTE register to be successful.
But I can't achieve the same effect using the program in...
Hello,
I'm using nRF52840( PCA10056 ) of SDK 15.2 to debug long range mode. And I have already followed the steps in thread: https://devzone.nordicsemi.com/f/nordic-q-a...
There was a similar question in the past, but I couldn't solve it by referring to it.
ESB communication between nRF24L01P and nRF52832 (PCA10040) fails. nRF24L01P...
I would like to remove the HEAP in my app to free up RAM.
I removed all explict calls to malloc and family.
I removed all variable length arrays, after finding that...
