I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I want use the NRF52832's NFC Tag in a bracelet. I need to know when the battery of the bracelect
is out, can the NRF52832's NFC Tag still be readable? Like the UID of the...
Hi
I add code in nrf5_SDK_for_Mesh_v0.10.0-Alpha_src, and when it run the follow code
and the ret_code is 4, I get information from the follow code
it is NRF_ERROR_NO_MEM...
Hi everyone !
I'm working with nRF 52840. I've downloaded softDevice s140 using Keil. Afterwards, I selected the target to nRF52840_xxaa and then build the project of Heart...
Not sure I understand the sentence. Do you guys mean "enabled"?
PSEL.SCK, PSEL.MOSI and PSEL.MISO must
only be configured when the SPI master
is disabled.
infocenter...
Lately I've been getting randomly occuring hardfault in my code during heavy BLE traffic and Sensor data collection times. From the hardfault_implementation.c loop I see the...
Hi,
Is there a size limit for the vendor specific service UUID? It looks like it should be 16 bits but I can't set more than 4 bits in my code.
I am using the uart central...
Hi everyone,
I wanted to know if it's possible to change the length of a characteristic's value after it has been put in the attribute table. Reading some other answers...
I found two bugs in the SPI master driver and I'm posting the solution here to benefit anyone else that may run into these bugs. I apologize if these bugs are old news. I...
I'm working on porting our connectivity application from SDK11/SD132v2.0.0 to SDK14/SD132v5.0.0.
Currently, though most Android phones I've tried can connect, the Moto...
Hi, I am working with the Mesh SDK 0.10.1. Everything compiles and runs fine. However I wasn't getting any RTT logs. I found that if I put a while loop before the first call...
Hi,
I would like to integrate BLE serialization with a nrf52832 and S132 soft device in a STM32 project.
I tried to identify which parts of the heart rate sensor example...
Hello,
I'm trying to flash my nrf52 DK but it's not detected by nrfgo studio.
here are the version of the softwares i'm using :
SDK : 14
JLink : 6.20g
Command...
Hello NorDev. community,
I have two sensors operating on nrf51822. I control them manually by mechanical switches at the moment.
I would like to change this sensor control...
hello everone
1、I tried the thingy52 sound demo ,but quality of the sound is bad, It is because the limit of the transfer speed？
2、I want transfer the sound by ble，how...
