Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Im try to read the RPD register, but always get the same value RPD=0
uint8_t channel=0;
int index;
hal_nrf_set_operation_mode(HAL_NRF_PRX);
hal_nrf_set_power_mode(HAL_NRF_PWR_UP...
Hi ,
I need the BLE peripheral to have 'name1' at the start up and change it to 'name2' when a button is pressed. I want to do this without disabling and enabling the softdevice...
Hello,
I'm in the process of updating our codebase to SDK 14 and am facing some problems getting the CLI to work. My goal is to get CLI and logging to output on the same...
[nRF52840 + SDK13]
On the hardware that I have, the UART driver is hitting a communication error because the RX line is low. This only happens when the UART lines are disconnected...
Hello,
I try to achieve maximum data throughput using pc-ble-driver 1.0 and nRF51(with ble_connectivity) as BLE dongle.
First problem I encountered was the bug with...
Hi,
we are currently testing the nRF52 DK as a reciever for several BLE devices.
For a fist test we implemented some datarate measuring in the:
PC -> nrf Connect -...
Hello,
I am using ndk52 (nrf52832) as peripheral and central in my system. I did some changes on ble-app-uart example for both. Now i can send my packets continiously....
Hello,
I am using ndk52 (nrf52832) as peripheral and central in my system. I did some changes on ble-app-uart example for both. Now i can send my packets continiously....
Hello,
I was wondering what is the best example to take as reference in case I want to pair two BLE devices automatically, I mean, I would like to make my devices to start...
i use RTC wakeup the sleep mode,project used the uart etc.
uart baudrate set to >=115200 sleep mode normally.but is baudrate set to <115200 sleep mode at 50ms+- periodic...
I am trying to use nRF connect's advertiser feature to simulate some sensor output for my testing. The sensors use BLE advertisements with scan response to send out data....
Hello community,
I am working in a central device with SDK 13 v. 4, PCA10400 (NRF52832) and SD 132 and one task is to receive 30 bytes from a sensors as a notifcation,...
Hi,
we are using are more or less unmodified version of the Secure DFU bootloader example. Especially all BLE/Softdevice configuration in "libraries/bootloader/ble_dfu...
As mentioned here , my poor little Thingy:52 doesn't work after upgrading to version 1.1.0 through the iOS app.
After getting my Thingy:52 i played arround with it for...
