Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hi,
I see there is a differenece between v1.0.0 and v1.1.0 in the asset tracrker's main loop.
i.e. poll function vs the sleep function.
does this result in a change...
Hi,
I'm working on a custom bootloader which does DFU over I2C. As a fail safe mechanism I want to have a timer running that gets reset between each Image data block, so...
When using SDK v13's I2S driver, the data to send is filled via data_handler callback. How do I fill last block data?
Assume i2s buffer size is 2000, then every 1000 words...
I have been going through the steps in this blog post: https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started-cellular/posts/getting-started-with-nrf9160...
Hello everybody,
I'll try to modify the ble uart example. The target is, to get data from two different nus Services (different characterisitv uuids). They are both initilised...
I basically need to use two UART instances with the BLE Buttonless DFU Template App.
I started using the Serial library but apparently it's no longer supported.
The methods...
Hello,
I am working on nRF52832 SDK 15.3.0 in segger studio.
In my project I have 2 ADC input pin.
ADC initialization is as shown below,
And every 0.5 second I read...
I have a custom BLE characteristic that I want to use to allow an app to send commands to my device. I use an on-write() function that is called whenever a BLE_GATTS_EVT_WRITE...
The Device's name UUID for Thingy52 in according to this site https://nordicsemiconductor.github.io/Nordic-Thingy52-FW/documentation/firmware_architecture.html is: EF68xxxx...
Hi I am using nrf52840 on a custom board with segger embedded studio as development IDE. I would like to flash the hex file generated without using segger embedded studio...
do you have a user gide for Serial DFU just like buttonless DFU ,like this link https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting-started-with-nordics...
Hi,
I have flashed lte_ble_gateway on nRf9160 DK (PCA10090) and hci_uart on nRF52840 SoC.
After flashing, I am getting some random RSSI values and MAC Address , instead...
Hello,
I have two micro-controllers communicating over SPI.
The STM32F746 is SPI master. The nRF52840 is SPI slave. I use SDK v15.3.
I am sending two bytes over SPI...
Hi.
I had to unpair from the Android Bluetooth list by doing pm_peers_delete () when bonding. It's ok. I know why it should. But sometimes I can't find my paired device...
