I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
Hello I am using the NRF52832 in ESB mode. I use both VERIFY_SUCCESS() and APP_ERROR_CHECK() within my code in various places but when am I supposed to use versus the other...
i have project app_ble_uart and i want add to it functin read from mpu6050 i add to Makefile Makefile pathes and add #include "mpu6050.h" and InitMPU6050(0x68); into main...
Hi,
I am currently working to measure power consumption on a custom board and I found huge power consumption while advertising (BMD-300 1.15mA DCDC enabled).
So I have...
Hi,
I am trouble with private key generation in nrfutil. I am following the tutorial infocenter.nordicsemi.com/index.jsp.
When I am giving the command nrfutil keys generate...
Hi, do you have a central peripheral combo example which illustrates indication (not notification)?
Alternatively, if you could list the steps to change from notification...
It seems GPIOTE interrupt do not trigger when multiple IN signals are defined as GPIOTE_CONFIG_IN_SENSE_XXX(false).
It works when GPIOTE_CONFIG_IN_SENSE_XXX(true)
I am...
With SDK 14:
If I flash in this order:
softdevice_s132.hex
bootloader_secure_ble_debug_ with bonds_s132.hex
3. ble_app_buttonless_dfu with _bonds_s132_with_setting_page...
I am having issues to use 2nd UART. When I run Keil in debug mode it shows me three UART registers.
i) UART0
ii) UARTE0
iii) UARTE1
Is this UART0 and UARTE0 same thing...
I am using NRF51822 Rev3 and softdevice 7 in my project. On communication with
Android device sometimes the link disconnects with disconnection reason61(0x3D)
BLE_HCI_CONN_TERMINATED_DUE_TO_MIC_FAILURE...
I have used nrf24l01+(production year=2015) in my project and my board and my program are working well......but when I change nrf24l01+(production year=2016) my board doesn...
I have an application where knowledge of the current date/time is important. This is implemented by the central passing the time to the peripheral when it initially connects...
I am able to flash/program nrf51822 with openOCD on Raspberry-pi and STLink-v2
but when I invoke Open On-Chip Debugger on telnet to write on UICR register, it don't give...
Hi everyone,
I am currently working on a project that leads me to save a respectful amount of data.
Some of the objects that I save size a few KB actually.
I would...
Estimate battery life for FOB CR 2032 -240 mAh
We are developing remote with CR2032 battery and using Nordic nrf51-1822 BLE, 960 m sec connection interval, RX 1 packet...
