Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
Hi, i am learning with thingy 91 x and nrf9151dk. I made the online courses and succesfully conect to the cloud with the nrf desktop quick start in both devices. Now, i would...
Hello,
I am working with a custom board that has the nRF52840 (via the ISP1807-LR-RS module). This board has the SIT1552AI-JE-DCC-32.768E MEMS TCXO. This TCXO chip has a...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
I use nRF51822 Model in my project that I need to run bluetooth advertising all time. And when I measured current, I found 1mA that is not enough to run for 1 year by just...
Hi,
My project include two MCU with n51822 and STM32. I expect upgrading STM32 application firmware by n51822 DFU function. Do you give your advice to implement it by modifying...
Hi All,
I am struggling getting my N548 module to transmit any ANT+ ...
I have tried the Cycling Power Sample Application (S310)
And the Cadense / Speed (S210) Sample...
Hello,
Is there any delay between when the reset pin is driven low and the actual reset of the chip. Would it be possible to sense the reset pin and perform some quick...
I am designing an nrf52 based device running at 1.8V. To debug the device I was planning to use debug out option of the nrf52 preview DK. However, I just find that, the debug...
I'm trying to follow the code from one of your examples, specifically ble_beacon in SDK 8.0 and eventually I get to a point where I'm not sure what's going on so I figured...
Hello,
I have question. I using examples with nRF51-ble-peripheral-bond-handling with bls_service (PCA10028) and i have problem with unnecessary connection. I want that my...
I'm referring this blog on getting started with nRF51822 and in this same blog, there is a link to a video by Nordic on Introduction to Bluetooth Smart and after watching...
I have two STM8s105 MCUs and two NRF24L01+ modules. Set one as transmitter:
CONFIG: 0x3A
EN_AA: 0x00
EN_RXADDR: 0x03
SETUP_AW: 0x03
SETUP_RETR: 0x00
RF_CH: 0x00...
Hi
I used the boot loader example successfully on the nrf51DK board.
Now I want to use it on my custom board. So I recompiled the boot loader code, with 1 difference:...
I don’t fully understand the nRF51 event NRF_RADIO->END. NRF_RADIO->END identifies the completion of a packet transmission or reception. My question is what triggers NRF_RADIO...
We have a project that involves both battery-powered 'slave' devices and a mains-powered 'master' device (which needs to support multiple slaves and support WiFi). We are...
Hi,
imagine that I have a proprietary characteristic that allows only READ operation (from a smartphone for example) that expose an internal value in my application.
I...
Hi,
I'm using nrf51822 and SDK 6.1.
devzone.nordicsemi.com/.../
I learned how to store data with using pstorage library.
but I can't register block more than 1024...
