Hello everyone,
I'm working on an NRF54L15 DK evaluation board and I need to use NFCT pins as normal GPIOs. I found out here that I should define CONFIG_NFCT_PINS_AS_GPIOS...
Hi all I am new to Nordic world. I have received a nRF5340 audio dk board and would like to be able to get VS code to build the default sample code - I have tried in windows...
We are certifying our device at KIWA. they are testing the WLAN adaptivity and the test is failing. Here is the failure description:
" It was a struggle to perform the...
I would like to try the new nRF54H20 but I can’t find its development board. I found this page talking about it, but I can’t find where to buy it online. Has it not been released...
Hi,
I want to configure P2.06 of my custom board nrf54l15 as DI. I have added following configuration in .overlay file
And configured the pin as input as follows
...
When attempting to register my nrf9160-dk device on nRF Cloud, I receive a message indicating the device is already registered. I do not know which account registered it....
Hello,
On nRF52832, I implemented a code with PWM output at P0.07.
Here is the section at my overlay:
pwmleds {
compatible = "pwm-leds" ;
pwm_led0: pwm_led_0 ...
I use the persistent storage manager for saving some calibration parameters. It seems to work ok - I can power off/on, and the values are still there.
However, after I...
Hi. I would like to get into bare metal programming, and have decided to go for ARM processors. Are there any ns-kits or courses availible for purchase?
thnx in advance...
I have a few questions regarding power-fail comparator (POF).
How much current POF consumes? About the same as low power comparator (0.5uA) or lower?
How will softdevice...
Hi,
my firmware works fine, but when I tried to do DFU using the master control apk, it would get to the download screen and then quit.
This is the text:
DFU version...
I wonder if I can ask about the leds intensity control:
I need to control the led intensity without the PWM because I'm using the softdevice & PWM didn't work with it,...
Dear All,
I'm trying to set a static passkey. I have created 2 custom characterestic. One characterestic is used for notifications and the other one for writing. For communication...
I'm making a peripheral device that should be powered off most of the time, but never idle if on, so I want to make sure that it is always (1) connected, or (2) advertising...
Now I have a project to build the schematic.
a, 5 LED indicators(0603) were driven individually by GPIO port directly, serial with resistor, then pull down to GND.
Is...
I installed nRFgo Studio Version 1.20.0.2 (which removed my older version) and was trying to program a softdevice (5.2.1) into our custom board and was presented with a popup...
Hello, I just received the nRF8002 development Kit and want to connect it to my windows 8.1 64bit machine. I get errors that there is no driver. Tried downloading the latest...
Hi, when calling sd_ble_gap_address_get from APP i get 0xXXXXXXXX4F and when i call it from DFU i get 0xXXXXXXXX50(X beeing the same), why is this? Is it a feature or a bug...
Hey Nordic--
I updated my Keil project from SDK v8.0.0 to v8.1.0 and immediately get some compilation errors due to redefinition of symbols.
In nrf_sd_def.h, I think...
Hi everyone. I have a strange problem. As we all know, there's a bug in SDK8.0.0 that dont allows to infinite advertising. To work this around i set advertising interval to...
Hi!
I am using nrf51DK with s110 soft device loaded on it to read data from Bosch BMA180 accelerometer using I2C interface. I would like to use clock prescaller and transmit...
