I'm not able to debug any of example applications that uses non secure build. Non ns versions works fine. I have added CONFIG_TFM_CMAKE_BUILD_TYPE_RELWITHDEBINFO =y to my...
Hi Team,
We recently received our custom PCBs and are currently trying to configure pins P1.00 and P1.01 as UART0 RX and TX respectively. However, the UART communication...
Draft — ready to post on Nordic DevZone / Zephyr mailing-list
Title nRF5340 DK + MCP2515/TJA1050 module — can_start() always returns -EIO even in loop-back
Hardware...
Hi We are working on setting up CI/CD pipelines for our nRF application. The application is set up as a stand-alone application with its own west workspace. It uses external...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
I want to drive motors at 40kHz and am wondering if I will be able to do this with the nRF51822. If not 40kHz, I might be able to go as low as 15kHz. What is the resolution...
Hi, I am using nrf51822 ble module. I want to have multiple such modules which could connect to a central device. How could I make it that the central device encourages only...
Hi, I am creating a custom service and corresponding characteristic. For that I am planning to use bluetooth base uuid (for confirmation : 0000 0000 -0000-1000-8000-00805F9B34FB...
Hi,
I`m working on our firmware for nRF51822 and I received the assert from soft device when turning off the global interrupts for our time-dependent procedure which have...
I am using PCA10001 board.
First of all i am unable to find nRF51 SDK.exe.
So i downloaded SDK form below link
link text
I changed device to nRF51822_xxAA.
Now i...
Nodic Semicond has made a nice step-by-step description for how to fix a corrupted infoPage.
It involves starting nRFgo Studio from a command prompt with "-defaultsettings...
Hi,
I want to make a connectable bluettoth transmission. I need 1 service with 3 characteristics, but for now I only want to see my service in app. It is possible to do it...
I have a nRF24LE1 processor.
We have an 'RF bootloader' which operates from the pc running a 'nRFUpdate 'Firmware over the air'' program using a dongle made by 'sparkfun...
i am running this code on my nrf.
const nrf_drv_timer_t TIMER_LED = NRF_DRV_TIMER_INSTANCE(0);
uint8_t flag;
/**
* @brief Handler for timer events.
*/
void...
I currently have both the nRF51 DK and nRF51 Dongle plugged on my PC. In Keil, when I try to load my program into the nRF51 DK I get the following error: "No JLink is selected...
HI People,
I face a problem when I do an OTA DFU from APP to APP. I compiled ble_app_hrs S110_with_dfu example fro sdk 9.0.0 and did OTA dfu. Now the device advertises...
I'm in the middle of putting a NRF51822 device through bluetooth certification. The test house has asked that I have modes where the radio is transmitting on certain frequencies...
Hello. I finally succeeded mouse keyboard combo. I use mouse sensor with SPI. I send mouse_move_data in loop. However, when I connect with the computer, the mouse pointer...
I am trying to debug a SPI application using Keil and the Eval board, but am having problems with control of the port pins. I am using pin 23 as the CS pin. it configures...
