I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately,which does not success. With setting radio configuration: TXPower,frequency channel...
Hello there
I am now using Nordic 52840 dongle hardware ready to be used as a zigbee sniffer, and I have seen that official documentation is feasible.
My current environment...
I am having trouble modifying simple_hal.c from the mesh SDK v4.1 when buttons are on Port1 instead of Port0 on a nRF52840. I have buttons on P1.01 and P1.02.
Everything...
We're attempting to move from v1.1.0 to v1.2.0 of the NCS, in order to take advantage of some driver improvements (particularly DPD in the SPI NOR driver. When we migrate...
Hi,
I am currently working on a custom product that uses module BMD-300 from u-blox, which has nrf52382 chip in it. My application works fine and now I want to integrate...
hi,
Im developing a mesh network based on the nRF52832. I want to send some long message(over 11 byte) without segment, so I enabled the EXPERIMENTAL_INSTABURST_ENABLED...
I turn on the Instaburst feature already , after that , I program serial example to 2 nRF52832 and run it with interactive_pyaci
when i try to do PacketSend with 20 bytes...
I am running a Bme280 sensor with nrf9160 and getting this error msg ( [ 1;31m<err> i2c_nrfx_twim: Error 195952641 occurred for message 0 ) while getting the actual sensor...
Hi All,
Since I measured a very current consumption by testing CLI example (ftd/usb) I'd like to know how to switch my nRF52840 DK as Sleepy End Device.
Any suggestion...
I have a zephyr sample app running on a nrf51822. It's the onoff_level_lighting_vnd_app found in samples/boards/nrf/mesh. I have an iPhone running nrfMesh. I can't find documentation...
Hello, Im working with nrf52832 and sdk15 I'm working with the example: nRF5_SDK_15.0.0_a53641a/examples/ble_central_and_peripheral/experimental/ble_app_hrs_rscs_relay I want...
How can I receive all the packets from all addresses?
In the datasheet I see there's an RXADDRESS which setups the receiver to which address it will listen to. I want to...
I am using the zigbee sdk4.10 cli_agent_router and multi_sensor example. The 52840 module is E73-2G4M08S1C, antenna is a built-in ceramic antenna. During operation, the communication...
Hi,
I have central based on the 840 and a Peripheral on the 833 , I Need to ability to upgrade the peripheral version from the central.
I know that there is no example...
Hi All,
I am trying to use the RNG peripheral through the softdevice (i am using Version 5.0, with 14.2 SDK) with the sd_rand_... functions. I have enable d the RNG in...