I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
First, many thanks for the great DFU recipe in the latest SDK!
I've ported OTA DFU to the IAR tool chain for both s110 and s310. I can flip back and forth between the two...
Hi,
I'm using IAR ARM Embedded Workbench (v7.20) to build my Nordic applications. Recently I enabled optimizations (in Project Options: C/C++ Compiler:Optimizations: Level...
Hi,
I am new to Keil and nrf51 development so please forgive me if I ask a stupid question.
I have followed the steps from the user guide and installed Keil (version...
I have scoured the internet for solutions, and documentation. Everything that I've found has to do with ADC, so I thought that I would just convert it to the LPCOMP(they're...
Hi all,
If I want to send a table that contains a structure in each of his cases using sd_ble_gatts_hvx(), can I get it ?
Knowing that the second parametre of sd_ble_gatts_hvx...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
S110 8.0.0 was just released allowing a larger ATT table, which is something we need, but is there a corresponding SDK update for this SD before we spend the time upgrading...
I am a very beginner on embedded field.
I have a nrf51822 and tmp 102. I follow this direction on mbed site
link text
and it's actually working. The code provide...
Hi,
I have a similar problem as described in
devzone.nordicsemi.com/.../
I have eliminated my program to be:
int main(void) {
setupLEDPins();
BluetoothPeripheral...
We are having some trouble with battery percentage measurement. The battery percentage being reported, keeps fluctuating. Earlier the fluctuations were as large as 3% to 100...
Hi,
I recently made some changes to the code and noticed the following errors for the first time.
Error: L6406E: No space in execution regions with .ANY selector matching...
Hi, all!
I am rencently studying ota,and that is what I have done:
Program softdevice 6.0 into my nrf51822 chip.
Program bootloader(version in SDK5.2) into my nrf51822...
hello everyone,
I recently purchased the new nRF51 dongle. I could successfully load the blinky example with S110 soft device to it. But it is not working with the HRS example...
Hi, I am trying to use your new sd 8.0.0 but there are a lot of compilation errors due to the new APIs and removed section from security structs in SDK 7.2.0.
Are we to sole...
Hello
I have the nRF51822EK PCA10001 (V1.0) and PCA10000 (V1.0).
I'm working on a project where i'm going to send data from a custom board over to the PCA10000 dongle...
