Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I am trying to write a radio code without using BLE stack here i was able to write down code for initialization of radio and was advertising some random packets. But how should...
Hi, I've got another question connected with pstorage module. Does anyone know what happens if we will call pstorage_update() function when we are trying to update some data...
Hi,
I have a custom board with nrf51822QFAA(256K flash) and I'm trying to test DFU-OTA (BLE transport) for an application. With only Softdevice and bootloader installed...
Hello,
I am developing using nRF51822 Beacon Source code and Beacon Hardware by Nordic.
I want to modify as below.
It never advertise by Intervel Time.
It advertise...
Hi,
I am developing a peripheral Glucose device.
I need to test my product but i dont have a central device or code.
Can you please help us with the central code for...
Hello ,
I am doing a new Keil project to run concurrently ANT for messagging exchange and Bluetooth LE for advertising.
On KEIL pack Installer I cannot find the example...
I want to implement the OTA update in nRF51822 on my custom board. I am using the bootloader example in the dfu folder for this. When I try this code on the DK, it works fine...
I am using nrf51822 with PCA 10001, SoftDevice S110 8.0.1. I try to compile the example "ble_app_proximity_s110_pca10028" and after I made a connection the device disconnects...
Has anybody had any experience in programming an nRF beacon kit over the air using the built-in Bluetooth Smart interface in a Windoze 8 laptop? (HP 255 G3) Is this even possible...
Hi,
I wanted to create fixed rate waveform. I first used nrf_delay_us with nrf_gpio_pin_toggle. But I realized it is not accurate enough to do it, especially when the device...
Hello,
I'd like to know how exactly do i implement this function in my app?
I tried getting the value from response (as shown in documentation) : ble_gattc_evt_char_val_by_uuid_read_rsp_t...
Hi,
My Jlink lite CortexM work with nrf51822 DK boards. But my PCB with nrf51822_xxAA chip can't download code. I'm using ukeil
When I chek in utilities Jlink can't recognize...
I am initializing an SPI master to talk to ADXL362 accelerometer using NRF51-DK.
Datasheet page 19: www.analog.com/.../ADXL362.pdf
No matter what I do connected or disconnected...
