Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I have noticed the PWM library in SDK v 8.1 randomly changes polarity of the PWM channels. I can't figure out what causes it to happen... seem's random, but I doubt it.
...
I am trying to upload the blinky example with the s110 softdevice into the nRF-DK board I just bought. The documentation says "flash_softdevice target". But I see no such...
Hello, according to the Product Specification v3.1, the supply voltage range is 1.8 V to 3.6 V.
As you may know, most of the lipo batteries have a nominal voltage of 3.7V...
I am following the NaN-36 example... So far all is going well but i am stuck at section 4.5.4 . I have checked over all the directions three or four times... I have to be...
I am hoping someone can point me in the correct direction as I have posted my question on the SIG forum and didn't receive any responses.
With a nRF51422 device is there...
I've followed the instructions for adding the DFU service to my app to the letter and can see the DFU service from the central and can enable notifications on the control...
Hi.
nrf51x22 has 32 IOs. can we assign 2 pin to usb d+, d-, and listen interrupt.
yes, nrf51x22 has uart support, but many host device only have usb port. serial port...
Hi All,
I am using NRF51822 chip pca10001 development board.
I flashed ble_app_hrs application to the board.
I configure 3 channel for PPI.
static void ppi_init...
Hello all,
I'm writing code for the nRF51 to allow it to be driven via the Android ANT SDK (from Dynastream), using standard ANT protocol messages.
However, it's occured...
Hi,
I'm using the nRF51 DK as a BLE sniffer with your Wireshark plugin. I have several BLE peripherals in the same room I'm testing it so it will be useful to filter data...
Hi, I'm newbie developing with nRF51. I'm working in Firmware for a ble central role that can read all the macs of ble peripherals roles near. I want to event or function...
Hi all,
I've a problem that drives me crazy for some day.
I installed all SDKs, and trying to write some BLE apps. Everything works fine but i cant't find where pstorage_access_wait...
