Hello! This is the third time I'm asking something about the same project, but I'm running into problems one after the other.
The current problem is this - the hogp object...
Hello,
I know this question is more related to Zephyr than Nordic, but I wanted to try asking here.
I’m using the SMP service to send files to my device on a LittleFS...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
Hi,
We're currently evaluating the cellular capabilities of the nRF91 modem using the nRF9151 DK. We've encountered issues with roaming: when the devkit is taken to another...
Hello, Nordic Team! I am encountering a such problem when using the NRF54L15 on NCS3.0.2 to develop a Matter product. I am trying to use the
SubscribeAttribute
method...
Hello Nordic team,
I've recently upgraded my application from nRF Connect SDK v2.7.0 to v2.8.0 , and the previous BLE Disconnect issue has been resolved — thanks again for...
Hi,
I’m using the Thingy:91X board with the nRF9151 chip, modem firmware version 2.0.2, and SDK version 2.9.0.
We’re encountering a serious issue: the modem does not reconnect...
Hi,
I'm having trouble increasing frequency of data TX using ble_app_hrs example on PCA10028.
I tried to increase the TX frequency of heartrate data to 100ms by configuring...
It seems that the nRF52 Development Kit mis-handles extended hex records. If it has type "04" records (extended linear address), it works OK, but if it has type "02" records...
We have an optical measurement system where we need to pulse LED and sample a phototransistor precisely during the LED pulse. The rate of sampling is 1 kHz and we plan to...
HI i need help in sending a data value of 700+ continuously
1)May i know how should i format my data packet to suit the current 20 bytes of data sent through BLE
2)Is...
Hi,
I am working on application in which I want to send 1000 or more samples using SAADC and BLE over standard master control panel APP of Nordic. For sampling analog data...
I'm trying to fully understand how DFU works and am going through the nRF5 SDK v11.0.0 example bootloader ( dfu_dual_bank_ble_s132_pca10040 ) and app ( ble_app_hrs_s132_with_dfu_pca10040...
[summary]
When I update app by Keil μVision, RAM setting is reflected correctly, but when I update app on OTA, RAM setting change is not reflected.
[condition]
Old...
Im trying to read flash memory ( N25Q032 ) identifier using SPI (NRF52) but then eveytime I try to read a register, the output is always zero, I tested with oscilloscope and...
Hi,
I'm using the nRF Dongle for sniffing.
Apparently there are many problems with the sniffer application.
First of all, the CTRL+R command for downloading the FW...
Hi!
I am trying to modify the ble_app_gls example from the 8.0.0 SDK and am running into some issues. I am trying to add the nus service to this example and would like...
HI dear:
We have two questions to ask you：
1、Can we customize two different BASE_UUID in the nrf52832 ? If we can,and how to do it,We can customize one BASE_UUID (128bit...
Hi there,
I'm new to the nRF52 and to ANT, so I'm in the process of running through some of the example code. I've been able to successfully run peripheral and BLE examples...
Hello,
i'm looking for the NRF52832 QFN48 6x6 symbol and footprint in Orcad/Allegro format to accelerate my design,
unfortunately, my electronic designer don't use Altium...
I've been experiencing this bug for a while now. What happens is that a app_timer's overflow handler can't put any more messages into the queue because the queue is full,...
I need to connect to the VSS of the nRF52832-CIAA Ground
A mistake by one of the VSS was not connected nowhere.
The VSS was one N.C..
Do you have any problem with...
