Hello,
I am using nrf52840 MCU.
I am developing a product which have 2 I2C and 2 SPI interfaces. All the interfaces are on different pins.
I developed this thing with...
Hello all,
I am using the nrf52840 MCU and NCS v2.6.2 for my application development. Here I am using SPIM3. I am using a peripheral which have an internal FIFO. From...
The partition config for ZBOSS is set in different locations in NCS. For us this worked out magically in the past because the values that were written have been the same in...
Hi everyone,
I'm working on a project using the nRF54L05 (v2.9.0) and I'm currently facing an issue with BLE. I want to change the BLE transmit power , and so far I’ve only...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi,
I’m trying to understand the following parameters in the nRF54L15 channel sounding configuration, because their function is not clear to me. I added my questions as...
I have been working on this for very long time but I can't figure it out, I am trying to use pc-ble-driver to connect my Ubuntu/Raspberry pi to by BT832X module over UART...
I flashed firmware into my nordic nrf52832 DVK
https://github.com/NordicSemiconductor/pc-ble-driver/blob/99b5e78f96de60ee70e749bb89b280116275fb97/hex/sd_api_v3/connectivity_1...
Hello,
I envisage to use beacon as anti-theft system:
When the beacon (inside the product to protect) will be near (2m) from the door, it will trig an alarm. So a receiver...
Hi,
I want to implement Extended Advertising for broadcasting data with LE Coded PHY on the nRF52840 Boards with Softdevice S140 v6.0.0.
For Soft Device Version S132...
This is basically a bug report/feature request, but I figured having it out in the open would be good too in case anyone else runs into this.
Hi Nordic folks,
Would...
Hi Expert,
I know how to read mac address by software ,
but I need to know how to read mac address by tool like nrfgo,
I tried nrfgo and nrfjprog but failed,would...
Hello,
when I try to update bootloader on nRF52 from SDK12.3 to SDK14.2 using DFU over BLE I get INSUFFICIENT_RESOURCES error. I think it is caused by different sizes of...
Hi All,
I'm working with SDK 12.3.0 and an nrf52832. I currently have 3 characteristics in my custom service. They are 17, 11, and 6 bytes long and are used to send sensor...
I didn't find any documentation on how to program nRF52 (specifically, nRF52832, nRF52810) using Keil uLink instead of SeggerJLink .
(specifically, I am using a ULINKplus...
Hi All,
I'm having issues saving large logs on Android (Pixel 2) with the nRF Connect or Logger app.
In the nRF Connect app, it gives me an error that the file is too...
Hi,
I work with a ship nrf52832.
I try to realise a communication beetween an UART sensor and the ship.
When i send my command ( app_uart_put) , i use nrf_delay_ms fonction...
I am running the app_beacon example for the nrf52810 at an advertising interval of 5000 ms and am getting a current draw of 300 uA.
I have the DC DC enabled, and am only...
Hi,
I have a compile problem in esb_ptx of SDK 11.0.0.
When I add a esb command "nrf_esb_rf_channel_get()" in nRF5_SDK_11.0.0_89a8197\examples\proprietary_rf\esb_ptx\main...
Hello everyone, I would like to change the name of my device with sd_ble_gap_device_name_set (). But the resulted name in the nRF Connect app is always "N/A". Here's my code...
