I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
I am using SDK 15 and i have successfully flash soft device , boot-loader and application code using nrfgo studio. Connecting using nrf connect application. Click on the DFU...
Hi,
We are transitioning a product from the nRF51 to nRF52832, and I am looking into what I need to do to get our code ported over and approved with the Bluetooth SiG. ...
Hi there,
I am a using a nRF52/SDK 13 to communicate to an external board which uses AT commands, I would like to save some battery during the time I perform my AT command...
I read that the old SDK for mesh had the provisioner and client as the same operation, as I am trying to make my own philips hue style wireless lamp I would need to get my...
Hi!
My question is for the purpose of power calculations for both the nRF52832 and nRF52840 for BLE use only.
I haven't been able to find a reference for this.
I see...
I'm trying to follow "Bluetooth low energy Advertising, a beginner's tutorial" by MartinBL found at https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble...
Hi, in my previous attempt to fix n52DK, I fixed the n52DK board's power rail. It turns out not the problem of the interface MCU shorting VDD.
But when I followed the instruction...
Hi All,
Just feedback from Lab, they said that they can set any channel frequencies at bandwidth = 1MHz in the Direct Test Mode. BUT they said that they need to test any...
Did someone try to make QT application that supports DFU for BLE devices? Can it be done using nordic DFU android/ios libraries (to include them somehow in QT project)?
Hi,
I am having a problems with USB enumerating with a custom board based on the nRF52840. The board is self powered by LiPo battery. I am developing by connecting to the...
Greetings,
I'm attempting to use the ble_connectivity example for the PCA10040 and have a couple questions:
1) What are the default GPIO pins for UART?, for SPI?
2)...
Can you provide an android application that can implement light control?A s shown in Illustration:
like the nRF Connect or LightBlue.the application as client not provisioner...
HI：
I am studying mesh now.But I don't know how to run this example.I think，that proceed as follows：
1.Using provisioner example Configuration each node(element and models...
I'm using SDK version 15.0.0_a53641a on nRF52840 with softdevice s140_nrf52_6.1.0_softdevice.hex.
When I execute the code below in ble_stack_init (void) , I get an error...
