Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi,
We need to collect sensor data from nrf52832 and after some processing, we plot data and generate some notifications etc. on smartphone app.
Shortly we need to design...
Hello, I'm developing a solution by using MESH SDK : nrf5_SDK_for_Mesh_v2.1.1
There is an ASSERT on access.c in nrf5_SDK_for_Mesh_v2.1.1_src\mesh\access\src\ as below. ...
SoftDevice: S132_5.1.0
Environment: I have 1 Device Advertising and about 200 "tags" waking up every 10 seconds and scanning for those advertisements and connecting, I have...
HCI for NRF52840
Hello
I m using a STM32 + NRF52840 and i have a mbed project in my STM32 and i want to use The NRF52840 only as a Bluetooth component, is there an example...
Hi guys,
I compiled the openbootloader example and when I try to run it on NRF52840, It gives segmentation fault:
(gdb) load nrf52840_xxaa_debug.hex Loading section .sec1...
Hi,
I'm having problem with the example code in the "Bluetooth low energy Services, a beginner's tutorial", the code was downloaded from github.
I'm using SES V3.5 for...
Hi,
We are currently develop our costum board with an nRF52840 SoC. Are the nRF52840 shipped with an initial bootloader to programm the device via USB? Because if possible...
Hello folks.
Easy question.
I want to add a .a static library to Segger Studio, but I don't know exactly where to add it. I know how to do in a Makefile with GCC, same...
I found the reference design files for nRF24LE1 from here ( https://www.nordicsemi.com/eng/nordic/download_resource/10898/2/41030525/1871 ), but I can't open them in EAGLE...
pca10059, replacing stock bootloader with Adafruit UF2, using USB dfu Hi. I currently don't have a J-Link at hand, so I tried to flash the UF2 bootloader using the stock DFU...
I want to keep both chip antenna and external antenna options on our board, what is best way to handle this for nRF24LE1 4×4mm QFN24 chip-set? Can I branch the Radio by having...
Hi,
I have a nRF52840 DK and a nRF52840 Dongle. I want to test to send binary data from one to each other using Bluetooth 5 or Nordic proprietary protocols. Are there...
Hi everyone, I am newcommer in here. I just buy one nRF52840 Dongle. I want to connect it with nRF52832 DK with ble_app_uart implemented; and open a COM port in MATLAB to...
Hi,
My application is based of ble_freertos_hrs example (SDK 14.2, nRF52832) and I need some variables to survive an assertion.
It appears that Keil has deprecated #pragma...
Hi Engineer： When I use nrf5_SDK_for_Mesh_v2.1 to debug the "light_switch" project, I always need to use a minimum of three boards (one as a provisioner, one as a client,...
