I enable cs procedure and set the procdure count equals to 3, let procedure interval to be 10.
I want to change the cs channel map between procedures. so when I send HCI_LE_CS_Set_Channel_Classification...
HI ALL,
I want to obtain the status of the upgrade process using mcuboot ble, such as flashing lights when starting the upgrade, flashing lights during the upgrade, and...
Hi,
I am working with the nRF54L15 and I want to use it both as a BLE central and as a BLE peripheral. So, I have two separate source files: one for central and one for...
Hi all,
nrf54l15dk,v3.0.1,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
Finally...
Hello,
I am working with the nRF7002 DK board and attempting to use the "Light Bulb Matter" example from Zephyr. I am encountering issues when trying to connect the board...
Hi
Our present build system on v2.6.1, builds variants of our baseline application using batch files.
It ends up building using west in this way:
The generated...
Hi,Team,
I am developing pawr using nrf54l15-dk. I wanted to set the parameters of pawr with 128 sub-events and 8 response intervals, but the setting Failed and the error...
Hi. I'm beginner of nRF.
I want to get some data from a temperature sensor, but I don't know how to assign a pin. Also, how can I check the data ??
In Arduino, there...
Hello,
I'm attempting to include the "arm_math.h" library so that I can use the requisite DSP functions, etc. I'm getting a linker error so I'm not sure what else needs...
HI,
I am using nRF52832 and SDK 14.2 and trying to send MPU accelerometer values to android device through BLE . But when I call " mpu_init() " in main function to initiate...
Dear Sir,
I am new to Nordic. This is my first query. It is related to running Timer with softdevice. I am using TIMER1 ( as const nrf_drv_timer_t TIMER_LED = NRF_DRV_TIMER_INSTANCE...
Hi, Support team,
When I use the SPI peripheral communicate with nrf24l01+,it's no data return in m_rx_buf by using the API nrf_drv_spi_transfer(&spi,m_tx_buf,1, m_rx_buf...
Hi,
I use the FDS on our project firmware. The firmware saves some configurations to FDS at shutdown and the factory reset. At this time, sometime fds_gc() does not call...
Sometime, the timer handler is not call immediately after calling app_timer_start().
environment - nrf52840 - SDK 15 - with FreeRTOS - timer task priority is higher - timeout_ticks...
Hi,
In the nRF Mesh mobile app, when you go to the settings tab, you can hit "Reset Network", this appears to clear any previously provisioned network, and lets you start...
Hi all!
We've been time-stamping GPIO events using PPI in nRF52 , and it works* !
...but when using the SoftDevice , it apparently clashes with the PPI about 30ms after...
Hello,
I have been having issues when using the UART libraries (app_uart.h) with certain pins on the nrf52832. Previous iterations of our project have worked correctly but...
I am investigating an H4 HCI over a UART implementation for a client which plans to use the 52832 (or 52840) as a replacement for a TI BLE chip in a new design.
I have built...
Hi all
We are using customized board with nRf52810 chipset.
Actual requirement in our project is to send 100 bytes of data for 10 millisecond.
Kindly suggest a procedure...
I'm developing multiple peripheral and a central. Central is only scanning and Peripherals are only advertising.
In the example, I see that I should use the ble_app_blinky...
Hi,
I was trying to run dfu mesh example according to this. I attempted quite few times but every time having an error at step 11.
infocenter.nordicsemi.com/index.jsp...
