Hi Nordic：
We are currently testing Zigbee on the nRF54L15 platform using the Zigbee R23-add-on-V1.0.0 SDK. It has been observed that when a low-power node disconnects from...
Hello, I am using ISP1907 which has NRF52833. I get the IQ data and configuration from serial as: DF_BEGIN ['IQ', 0, 0, 11, -9, -213] ['IQ', 1, 8, 11, -209, 23] ['IQ', 2,...
I have 2x Power Profiler Kit II up and running using the Power Profiler app - started twice and with separate PPK2 instances selected, as described in another support post...
Hi, I am running openthread on the NRF54l15 DK. Whenever I am debugging and hit the breakpoint or pause the program, then on resumption my app crashes. How Can I debug while...
Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
Hi Everyone,
I am working on a hobby project with nRF51822 which needs me sample upto 4 signals reliably at 500Hz each at 10bit resolution. I have read through few posts...
Hi all,
I have two nRF52 connecting, transmitting, disconnecting and sleep mode when are in normal operation, now I am experimenting a randomly error code 8 when calling...
Dear Nordic Team,
Meanwhile, I've burned through a week finding a solution for this problem.
Now I am out of ideas where to check for problems.
My application:
I...
Hi, I use the following.
Raspberry Pi 3 (RPi3 with Raspbian Jessie 4.4) as a router,
RPi3 is connected to a Wi-Fi router to access the Internet by using the built...
I'm trying to flash a nRF518122 with a St-Link V2 programmer via Open OCD.
The process seems to goes smooth, but comparing the number of written bytes to the actual HEX size...
How is BLE_CONN_HANDLE_INVALID changed in multiple services
I modified the ble_sdk_app_proximity example. I added x3 services, based on the BLE Characteristics, a beginner...
Hello
im building a project for discovering infections through temperature sensors, so im modifying the heart monitor sensor examples (central and peripheral) in the sdk...
Hi
I am developing an applicaztion with SDK 13.0.0 and S132 for nrf52832
The version of the softdevice to be used with this SDK is 4.0.2, and I need access to L2CAP layer...
First,the meizu phone can dfu successfully in the dual bank mode,
So do the 360 phone.
But in single bank DFU,this two kinds of phone failed,
So I make the programm enter...
I'm designing custom board with nrf51822 SOC & using buck-boost converter for powering nrf chip, If I don't add inductors in DCC line how it will effect my custom board. ...
Hello,
In previous version of SDK, I used to use "sd_nvic_systemreset()" function to reset nRF52, but this function disappeared in SDK12.2.0 .
The question is what the...
Hello,
I am receiving the above error on Android BLE app while connecting to my pca10040 based board, and I developed this app with nRF Toolbox as a reference.
I am...
Hi all,
I have understood that sys_evt_dispatch is used for all events that aren't BLE but concern the softdevice.
I start to develop my code on gls_example, here in...
