Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hi,
I am programming with ncs v2.9.0, nrf52833 chips.
I am going to get pc keyboard led state in my custom board throutgh BLE.
This is my report map,but cannot get data...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Hi.
I'm using nRF51822AC, SDK12.2.0 as Central.
Q1. Is there any function to know regarding it is scanning or not?
Q2. As your example "ble_app_multilink_central",...
Hello,
I am using two NRF52's to test out indications.
I have modified the Heart Rate Collector Application (Central) and Heart Rate Application (Peripheral) examples to...
Could someone paste the link to bluetooth specification v4.1? I can't find it on web. Probably it is avaliable only for SIG members, but I'm only a student and registration...
Hello, Dear friends,
I am new to Nordic, just have nrf52832 board come back, seems the current is higher than I expected before I program it.
does anybody know what is the...
Hello,
After digging through similar questions and answers I am still unable to build my code due to compiler errors. I am receiving these 5 errors:
Error: L6218E: Undefined...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. I am trying to use PWM to control a buzzer. To do this I included the following files into...
Hi,
I use Multilink Central and Experimental_ble_app_blinky examples.
Multilink Central sends only 1 byte. I want to send more.
Blinky does not work when I change the...
Hi all,
is there a way to set a characteristics when a read command arrive from APP, or it's necessary to set it before to read?
I see for example battery service, it...
How do I get data from a scan response packet using master emulator?
I do know about
BtScanParameters scanParams = new BtScanParameters();
scanParams.ScanType = BtScanType...
Hi, Nordic
Now, I have one nRF24 Dongle, two nRF52 devices.
two nRF52 devices will send data to nRF24 via ESB(gzll), but need to pair.
Can two nRF52 devices can pair...
What is the most energy efficient microphone input method, PCM via I2S or PDM. Does the SoC have a special HW handling of the PDM format for converting to PCM? Does the filtering...
Hello,
I am developing custom HAL driver for TWIM in NRF52 (PCA10040). The problem is that after the slave device stretches the clock signal, ninth period on SCL clock is...
Hi, i use the original ble_app_template (sdk11) with two lines of code added by me (See below) which erase the last page in flash (flash_page_erase((uint32_t *)(pg_size *...
