Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hi, I would like to send data from nRF52840 Dongle to Raspberry Pi 3 through USB-UART. I programmed the ble_app_uart_c example found in SDK 15.2 and I connected that to my...
NRF51822 RM 3.0 section 14.1 states each GPIO pin has DETECT, but where is the register to read per-pin detect? From the manual: "Each pin has a separate DETECT signal, and...
Hi,
Now, i want to use SAADC with softdevice of SDK15.0 to make a beacon program.
I migrate SAADC example in nRF5_SDK_15.0.0_a53641a\examples\peripheral to beacon with...
Hi,
I am using nrf_sniffer_2.0.0-beta-2_10Sep2018_3ef662e for capturing ble mesh packets but i am finding LE LL packets of my node with mesh beacons in my wireshark. Even...
Hello, I am new to nordic sdk and tools. I am planning to develop a nRF52840 DK based sensor device that reads I2C temperature sensor data ad broadcast it periodically. Also...
Hi,
I'm testing the BLE_UART example : <InstallFolder>\examples\peripheral\ble_app_uart . For this, I use the nRF52840 with SDK 15.2 and s140 softdevice.
I would like...
So I am using nrf52832 and making a whole new app in ios. My objective of the app is to get the sensor data (specially motion sensor data and accelerometer data) which is...
Hi,
I am trying to add app_uart into the heart rate sensor example. I called uart_config(); in the function function, but when I open the serial monitor, The errors shown...
Trying to build the unmodified light_switch_client_nrf52832_xxAA_s132_6_0_0.emProject from a fresh download of the Mesh SDK.
SDK_ROOT set & successfully tested as instructed...
Hi Team,
This is more like a generic question.
I have 100 beacons and I want to test them all simultaneously kind of a bulk testing.
What are the possible candidates...
Hello,
I would like to use the hardware crypto engine that is a part of nRF52832 chipset. I understand that the access to it is restricted as SoftDevice uses it. I wonder...
I am running into these 3 errors while compiling my program. I tried fixing sdk_config.h.
.\_build\nrf52832_xxaa.axf: Error: L6218E: Undefined symbol app_uart_init (referred...
EDIT: I have added the battery data in percentage to scan response manufacturer specific data. Is that the only possible way?
Hello,
I am working on a beacon application...
Recently, I was trying to use the button to select the specific actions.
Actually, the program is built successfully and it can show the "UART Start!" via serial port, but...
Hi everybody,
I am trying to read a 1024 bytes FIFO buffer from an IMU (Bosh BMI160) using the SPI master driver on nrf52832 and sdk 12.2.
I know others had the same...
