This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
Hi !
I just got my new boards with the NRF52 CPU.
When i burn the firmware that worked on the PCA10040 evk it works but on my hardware it resets immidiatly.
On my...
Is there a UART bootloader available for nRF52840? Doesn't have to be secure.
Already searched in SDK 12.2 and 13 alpha, with no success.
Thanks for your help!
I installed the latest JFlash (6.12d) from Segger's site, and it updated the JLink firmware.
However when I try to program the hex files downloaded from www.nordicsemi...
The macro NRF_DRV_SAADC_DEFAULT_CHANNEL_CONFIG_DIFFERENTIAL does not set the .burst field in the nrf_saadc_channel_config_t structure.
The macro NRF_DRV_SAADC_DEFAULT_CHANNEL_CONFIG_SE...
The app_fifo support e.g. in SDK 12.1.0, appears to have a serious problem when the read_pos/write_pos values wrap. i.e. when the fifo has been used over a period of time...
I have BLE400 extended board for nrf5. It has cp2102 on board from Silicon Labs. I installed drivers for mac and can see NRF_LOG_INFO via terminal. It would be great to have...
i am using nrf52840 with sdk 13.0.0-1.alpha. I want to boot the application from bootloader but by
using UART as a transport layer.
Would you plz help me?
I found end of address of fstorage from macro of "#define FS_PAGE_END_ADDR (fs_flash_page_end_addr())". But I want to change the start address of fstorage. Which macro or...
I have multiple GPIOs that are configured to use GPIOTE in my application. When one of these GPIOs is in the active state I start timer. Once the timer expires I want to enter...
Dear Nordic Team,
Thanks for supporting.
Currently i am try to work with VL53l0x distance sensor. Basic communication working good, but i am not able to get distance...
Hello
I tested a BMD-300 Module and Nordic Team has been very helpful.
I tried to reach the maximum speed in this module.
I like to send 4x20 byte per 30 ms, but I...
Hi all,
I am using as base the Experimental ble_app_blinky_central and ble_app_blinky examples.
I noticed using a sniffer that the Central is asking to the peripheral...
Hello,
I am going to us the meander antenna from the nrf51 usb dongle. Are there any drafts with correct dimensions? And second what should be the minimum distance between...
