I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
How can we decrease the resolution of the timer to 500 ms in SDK 14? The minimum resolution I could get to was 1 ms by changing the APP_TIMER_CONFIG_RTC_FREQUENCY macro to...
It seems that none of the distributors listed on the web page for the 52840-Dongle have them in stock. Is there another way to order some of the dongles?
Also can someone...
Hello,
I have a peripheral (nRF51822, S130, using the peer manager) that should be paired/bonded with at most one central. This means that if I want to pair the terminal...
I still can't see anything in the SDK documentation which tells me how to add an nRF5 SDK library to an existing project.
Specifically:
What source file(s) do I need...
Hi All;
I have been banging my head with this problem for days now. I am in the process of migrating our production FW from SDK 11 to 15 and doing some re-architecture...
Hi
currently I am working with the nRF52840 Preview DK. Using the on-board J-Link interface I can send debug messages to the debug console of the Segger Embedded Studio...
Hi,
I have tested AES-CCM of nRF52832 with reference to the following answered questions.
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
devzone.nordicsemi...
Dear all,
I did below steps to connect to the BluFruit Feather board via STLink V2:
1) Install OpenOcd and STLink USB driver as: https://pcbreflux.blogspot.com/2016...
I have some code originally working using SDK 13. It reads data from the UART and send it out in scan responses. iOS was able to capture the scan response data successfully...
hi all,
Our application is a peripheral device with sensor data that is sending up to 540kb/s (68kB/s) to the central device (data rate could probably be reduced if necessary...
Hi,
I'm trying to take the readings of temperature and humidity from 4 Nordic Thingy:52 sensors by using mesh. I did the connection of the mesh and I can control the nodes...
Hello,
I am new to BLE so I am not sure where to start. I have two nRF52832 chips, one will receive data from an FPGA through SPI and then I want to send the data to the...
For reference, in case anyone else gets a similar issue :
Using the SES import facility to import a Keil MDK v5.25 Project.
After fixing a couple of other import errors...
Hi @ll,
I'm not able to receive any ble events that should be triggered by the SoftDevice.
What I did: - Using dfu_example (added beaconing advertiser and connectable...
