Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
I am working on a custom board based on nrf52810 that my client provided. In this board the accelerometer (Bosch BMA250E) power has been controlled by the PIN 9. However when...
Hi, everyone
I have some problems to make the Image Transfer Demo APP work
I have read the content of the website( https://github.com/NordicPlayground/nrf52-ble-image...
Hi,
I have 2 devices: one nrf52832 and one nrf52840 dongle. After enabling PHY feature (see the following code) in nrf52832, I tried to connect it using the dongle in the...
Hi,
I got the following hardfault when running sdk 14.2, nrf52832. Since the address shows it locates in softdevice...I do not know why. May you please give me tip? Thanks...
Hello, we have a handheld device with Microchip (ex. Atmega) Microcontroller that essentially monitors and records different environmental conditions and stores them them...
I am making PUC for sending & receiving string through ble nrf51822 to phone(nordic app) with particular user define time interval like 1 min , 5 min etc. using ble_app_uart...
I'm running \nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral\ble_app_uart\pca10040\s132\arm5_no_packs and following instructions from http://infocenter.nordicsemi.com/index...
Hello,
We are using in nrf51822 in a product.
I do not understand whether by definition and, thus, always, before connecting, whether a peripheral
goes to sleep between...
Hi,
our device has a hard current limit of 2mA. Normal BLE operation is actually no problem. Connection parameters and packets/event are negotiated accordingly between master...
Hello,
I am using nrf SDK 15.0.0. I am unable to build ble_app_uart example in SES. It shows this error in the screenshot:
But i can build the same example using Keil...
Hi everyone,
I want to set LF CLK source to XTAL without softdevice. But, LFCLKSTAT value is 0x00010000(CKL RUN, CLK SRC = RC) after clock start.
So, I checked same test...
When drawing lines of equal start and end x, y coordinates the GFX library shall draw a rectangle with thickness applied. If the value of the opposing axis has a start value...
Hi everyone,
This might seem like a silly post, but this happened.
I build and ran the example QSPI code given in the sdk.
But after that if i try to run my own code...
We're writing code that does dynamic pin assignment which may change over time. This question is about how the crossbar deals with conflicting pin settings.
If I set the...
