VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
Hi,Sir:
I am developing a 52840’s project using SDK15.1,My development environment is Segger embedded (version 3.34a).When I added the RNG function to the code (the correct...
Hi,
Have an issue with a prototype 2 layer 52840 pcb that i tried to get manufactured. i increased the pad diameter to 0.3mm and now i cannot route without hitting clearance...
Hi
when trying https://github.com/NordicSemiconductor/IOS-nRF-Mesh-Library everything goes OK (I think...) all the nodes gets provisioned, all the elements gets addresses...
I know the PDK design is available for download, but there are a lot of things on that board which would not be required for a minimal e.g. beacon design
I'm looking for...
We are looking at developing a proprietary protocol using the nRF52832/40 and were interested in the specific and practical differences between the Ble_2Mbit vs Nrf_2Mbit...
We try to implement DFU over UART. The Mesh DFU example has been taken as a reference. DFU is successful, but it takes about 1 hour (sic!) to transfer DFU ZIP package of size...
Hi,
We are developing a device which should have a power save mode where no BLE connection is possible (switch off the BLE to a minimum power consumption) and restart the...
Hi, there~~ Just noticed that there are codes for the Android nRF connect.
github.com/.../Android-nRF-Connect
Using that code, I wish to create my personal sniffer that...
Good afternoon,
I'm using nRF52840 with SDK15 and Softdevice6.0.0.
I'm using the Queued Write Service Module to make use of a characteristic able to receive up to 510bytes...
Please suggest a tool that can be used for monitoring and and analysis of Nordic's BLE packet transmission rate.
I would like to measure packet irregularities over time...
HI,
How to use sd_ble_opt_set() with the option BLE_GAP_OPT_SCAN_REQ_REPORT ? After setting this I can expect to get the event "BLE_GAP_EVT_SCAN_REQ_REPORT" with information...
Hi,Support Team
I Use the nRF51822 SOC for SDK12.3-example-DFU-bootloader_secure, when I Select the ZIP upadate file,it has a reminder "Loading file has failed. Try different...
Hi,
I use buttonless DFU with the secure bootloader.
When I push a button my application advertise in fast mode with an interval of 40ms and for 5s. After it return to...
